Service Hotlinelead screw nut is provided with a through hole in the center for the screw rod to pass through, the surface of the through hole is provided with a screw thread engaged with the thread on the outer surface of the screw rod, and the surface of the through hole of the lead screw nut is provided with a thread along the surface of the through hole. The oil storage groove in the axial direction, the depth of the oil storage groove is greater than the depth of the thread.
Traditionally, the pressure rivets on the product are all beaten by hand by workers, resulting in high scrap rate and low efficiency, and this rivet is not a traditional rivet, so it is difficult to locate and requires high pressure. The rivets are thin, and the pressure is too large to cause deformation of the rivets. If the pressure is too small, it cannot be riveted. Without special positioning and tooling, it cannot be riveted on the riveting machine. The quality of the products produced in this way is difficult to guarantee, and the quality levels of the products in the same batch are uneven. Affect delivery time.
Usually, the forming of the bolt head adopts cold heading plastic processing. Compared with the cutting process, the metal fiber (metal wire) is continuous along the shape of the product, and there is no cut in the middle, thus improving the strength of the product, especially the mechanical properties. The cold heading forming process includes cutting and forming, single-station single-click, double-click cold heading and multi-station automatic cold heading. An automatic cold heading machine performs multi-station processes such as stamping, heading forging, extrusion and diameter reduction in several forming dies. The processing characteristics of the original blank used by the single-station or multi-station automatic cold heading machine are determined by the size of the bar with a length of 5-6 meters or the wire rod with a weight of 1900-2000KG, that is, the characteristics of the processing technology. The point is that cold heading does not use pre-cut single blanks, but uses the automatic cold heading machine itself to cut and upset (if necessary) blanks from bars and wire rods. Before extruding the cavity, the blank must be shaped. A blank that meets the technological requirements can be obtained by shaping. Before upsetting, reducing and positive extrusion, the blank does not need to be shaped. After the blank is cut, it is sent to the upsetting and shaping station. This station can improve the quality of the blank, reduce the forming force of the next station by 15-17%, and prolong the life of the die, and the bolts can be made with multiple diameter reductions. The precision that can be achieved by cold heading is also related to the selection of the forming method and the procedure used. In addition, it also depends on the structural characteristics of the equipment used, the process characteristics and its state, the precision of the tool and die, the life and the degree of wear. For high-alloy steel used in cold heading forming and extrusion, the roughness of the working surface of the cemented carbide mold should not be greater than Ra=0.2um. When the roughness of the working surface of this type of mold reaches Ra=0.025-0.050um, it has the highest life.
drilling and tapping screw, more specifically, refers to a drilling and tapping screw that can be closely connected to an object without clearance. Screws usually use a screw design to achieve the purpose of tightening, or adjusting distance, or moving or transmitting power. Among them, it is the most common for tightening, and the screws generally used for tightening also usually have The combined function of self-drilling, tapping and locking can achieve the purpose of its tight fit. Known drilling and tapping screws are such as
rivet dismantling method and a dismantling device thereof. The dismantling method firstly places a riveting piece with a failed rivet installed on a die having a blanking hole, and then uses a punch that coincides with the center line of the rivet on the riveting piece to impact the rivet. , the rivet falls into the blanking hole under the impact of the punch to complete the disassembly; the dismantling device includes a concave die for positioning and supporting the riveting piece installed with the failed rivet, and the concave die is provided with a blanking hole; The upper part of the die is provided with a punch for punching the rivet into the blanking hole, and the punch and the center line of the rivet are coincident; Yueluo adopts the punch to dismantle the failed rivet, which not only has high work efficiency, but also has high work strength. It is small, and does not damage the riveting parts on which the rivets are installed; the impact process will not cause the rivets to splash, and the safety is high; and the cost of dismantling equipment is low.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: outer hexagon lock nuts, GB91, a large number of supply nuts, GB93 spring washers DIN934 hexagon nuts and other products, we can provide you with suitable products for you fastener solutions.
