Service HotlineAt present, there are mainly the following methods for classifying screws of different lengths mixed together: First, visual identification and manual sorting. This method is time-consuming, labor-intensive and inefficient. Second, the screws are centrifuged and screened according to the quality and size of the screws. However, the quality of screws of the same length is not necessarily the same when the materials of the screws are different. Third, sorting is carried out using a screening device with sieve holes, but the sieve holes are generally simple geometric shapes, which can only roughly distinguish the length of the screws. Moreover, the specific position where the screw falls into the screen hole will also affect the degree of screening. It can be seen that the above-mentioned methods for classifying screws all have the problem of poor effect.
In view of this, a screw with waterproof, anti-loosening and anti-removal functions is provided. A screw comprises a screw rod and a screw head connected with the screw rod, the diameter of the screw head is larger than the diameter of the screw rod, and an annular groove is formed around the screw rod on the surface of the screw head connected with the screw rod, The screw head is also provided with a through hole penetrating the screw head, and the through hole is communicated with the annular groove for filling the annular groove with adhesive substances. Compared with the prior art, the screw provided by Guangdong Yueluo Hardware Industry Co., Ltd. has a structure in which a through hole and an annular groove are arranged on the screw head, so that after the screw is locked into the screw hole, the screw head is not locked. A glue storage flow channel is formed between the contact surface with the part, and then the glue material is injected into the glue storage flow channel through the through hole to form a sealing annular rubber ring, so as to better ensure the waterproof performance of the screw joint. Furthermore, by connecting the through hole with the screwdriver groove, while forming a sealing annular rubber ring, the driver groove can be directly filled for the purpose of preventing dismantling.
Stamping die is a special process equipment for processing materials into parts in cold stamping processing, called cold stamping die. Stamping is to use the die installed on the press to apply pressure to the material at room temperature to make it produce Separation or plastic deformation to obtain the required parts of a pressure processing method, the technology generally used is to make corresponding holes and punches on the template, this method cannot meet the requirements for small batches and short delivery time products , the relative cost is relatively high, so a rivet die structure is required to improve the above problems.
The composition and proportion of this high-performance stainless steel screw thread are: 0.08%-0.15% C; 0.01%-0.60% Si; 0.02%-0.60% Mn; 0.01%-0.03% P; 0.002%- 0.03% S; 12%-14% Cr; 0.8%-1.5% Mo and the rest is Fe. The preparation method includes the following steps: smelting molten steel according to chemical composition requirements; hot rolling; annealing and pickling to obtain a stainless steel plate blank; coating and drying; cold drawing; cleaning and drying with a neutral activator; quenching; tempering ; coated and dried; drawn into stainless steel thread. This high-performance stainless steel screw line is energy-saving and environmentally friendly, with high corrosion resistance, high elasticity and high toughness. The preparation method and process are advanced and simple, and the production cost is low.
The gasket side of the above-mentioned nut assembly is in contact with the mounting surface. When the nut is tightened, the gasket squeezes the outer cone surface to make it shrink, and the cone tip faces the same direction as the nut, thereby preventing the nut from tightening, so that the nut fixing effect is not good, and at the same time When multiple nuts need to be superimposed and fixed, two adjacent nuts cannot interact with each other, resulting in poor fixing effect.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flange face nuts, thick nuts, flat end set screws, flat head rivet nuts and other products, we can provide you with suitable products for you fastener solutions.
