Service HotlineMany existing products need to use screws in the production process, especially in the field of nuclear power sluice gates, it is necessary to fill a part of the sluice gate with screws to fix the size and structure. If the fixing effect is not good, then It will lead to more leakage of water gates, waste a lot of water resources, and even cause safety accidents.
Axle card is a kind of hole-to-hole movement installed on a slotted shaft and used as a fixed component. The inner diameter of this type of retaining ring is slightly smaller than the diameter of the assembly shaft. Application No. 201621153710.9 discloses a shaft card assembly device, including a feeding mechanism, a material distribution mechanism, a material reclaiming mechanism and an assembling mechanism. The feeding mechanism is connected with the feeding mechanism. The reclaiming mechanism includes a reclaiming tool and a servo system for driving the movement of the reclaiming tool. One end of the reclaiming tool is provided with a c-shaped opening, and an incision connected with the c-shaped opening is provided. The assembling mechanism includes a carrier for fixing the parts to be loaded and a turntable, and the carrier is mounted on the turntable. In the above shaft card assembly device, after the feeding mechanism completes the feeding, the material distribution mechanism separates the shaft card to a specific position with a fixed attitude, and then the private server drives the reclaiming tool to clamp the shaft card and assemble it to the pre-fixed by the assembly mechanism. on the fitting. During the assembly process, the manual workload is small, the efficiency is high, and the labor intensity is small. At the same time, the c-shaped opening and the cutout at the end of the reclaiming tool are designed to effectively form an elastic force to clamp the clamping shaft card and absorb the assembly process. The resulting outward deformation force avoids the plastic deformation of the shaft card due to the large external force.
The retaining ring is a ring-shaped body with an opening, and the traditional processing method is stamping. That is, a plate-shaped material is selected and punched out on the plate-shaped material (a circular body, and then the middle of the circular body is punched to form a ring-shaped ring body.) The punched material in the middle cannot be used again. This results in a waste of material.
At present, in the power industry, for the fixing of terminals, most of the terminals are directly locked to the fixing screws using U-shaped clips. However, since the contact surface often cannot reach the level of flatness, it will cause difficulties in locking, and it will take a long time. Easy to loose and fall off. Although the use of spring clips is effective, due to the influence of its own width, the use of spring clips is not very extensive. Contents of the utility model The purpose of Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to provide an automatic locking screw for fixing the U-shaped clip. In order to achieve the above purpose, Yueluo adopts the following technical solutions: an automatic locking screw. From bottom to top, there are screw head, screw rod and nut with external thread. The screw rod is a hollow screw rod, and the hollow screw rod is on both sides. Long holes are respectively provided, the width of the long holes is smaller than the inner diameter of the hollow screw rod, a spring is arranged in the inner cavity of the hollow screw rod, the upper end of the spring is provided with a plug, and the two wings of the plug protrude out of the hollow screw rod through the long hole. The spring described by Yueluo is not less than the length of the hollow screw rod in the free extension state. The distance between the two wings of the plug described by Yueluo is greater than the diameter of the nut. Yueluo adopts Guangdong Yueluo Hardware Industry Co., Ltd., which can easily realize the automatic locking of the U-shaped clamp, and can be adjusted according to the thickness of the U-shaped clamp to ensure the close contact between the U-shaped clamp and the connecting screw.
The capped nut can prevent the bolt connection from directly contacting with the outside world, which is corroded and makes it difficult to disassemble later. Nuts with caps in the prior art are mostly of one-piece structure, and the surface is not treated with anti-oxidation, which is easy to be corroded. In addition to the protective effect, the fastening method is the same as that of ordinary nuts, so it is easy to loosen when subjected to severe vibration. .
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: fine-tooth hexagon buckles, cup head hexagon bolts, hexagon socket machine wrench bolts, extended full-tooth hexagon screws and other products, we can provide you with The right fastener solution for you.
