your location: 首页>>News>>Industry News

Service Hotline

+86760-8787 8587

Customized 12.9 grade inner hexagonal concave end tightening Kimi screw top wire headless stop payment machine meter nail

author:[email protected] Click:6679end source: time:2022-08-05 21:06:12

Summary of information:We have more than ten years of production experience in the screw industry, the main products are: multi-axis aerial pho...

In steelmaking plants, the wheels of metallurgical casting crane trolleys used for hanging liquid metal are connected with cardan shafts through flanges. Usually, a keyway is set in the radial direction of the connecting flange, and the keyway is a through groove. The B-type flat key is set in the keyway to transmit torque. During the frequent forward and reverse motion of the wheel, the flange connection bolts are easily loosened. Since the keyway is a through groove, the B-type flat key is easily caused when the flange connection bolts are loosened. It falls off from the keyway of the connecting flange and cannot transmit the torque, which seriously affects the working efficiency of the locomotive. In addition, because the B-type flat key falls off and cannot transmit the torque, the locomotive can only rely on the connecting bolt to transmit the torque when it continues to work. Poor, it is easy to damage and scrap the connecting bolts, and then damage the connecting flanges, requiring frequent replacement and maintenance, high cost, and difficult maintenance.

Flat washers are usually thin pieces of various shapes used to reduce friction, prevent leakage, isolate, prevent loosening, or distribute pressure. Such components are found in many materials and structures to perform a variety of similar functions. Restricted by the material and process of threaded fasteners, the bearing surface of fasteners such as bolts is not large, so in order to reduce the compressive stress of the bearing surface and protect the surface of the connected parts, washers are used.

The existing way to achieve radial locking of the shaft is generally to sleeve the positioning block on the shaft, and then use a cylindrical pin to pass through the positioning block to lock the shaft. The locking structure and method are as follows: A locking groove with an arc-shaped cross-section is set on the outer side of the shaft along the direction perpendicular to the axis of the shaft, an opening is set on the positioning block, and then a cylindrical pin is used to pass through the positioning block from the outside of the positioning block and screw the lock at one end of the cylindrical pin. When the lock nut is tightened, the opening on the positioning block will be deformed inwardly and locked on the shaft.

Guangdong Yueluo Hardware Industry Co., Ltd. is a kind of locking nut, which includes a nut, the bottom of which is circular, the middle is hexagonal, the top is circular, there is a bolt hole in the center, the side wall of the bolt hole is threaded, and the top of the nut is Set up several squash notches. According to the locking nut of the preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the number of flattening notches is three. The three flattening gaps can be used as the focal point of the tightening tool and the clamping place of the anti-loose gasket bayonet, and the structure is simple and can be formed by die stamping at one time.

Gears, mechanical components with teeth on the rim that can continuously mesh to transmit motion and power, are mechanical parts with teeth that can mesh with each other. The gears used in industry are generally made of steel. The commonly used steels are quenched and tempered steel, hardened steel, carburized and quenched steel and nitrided steel. The strength of cast steel is slightly lower than that of forged steel, and it is often used in Larger-sized gears; gray cast iron has poor mechanical properties and can be used in light-load open gear transmissions; ductile iron can partially replace steel gears; plastic gears are mostly used in places where light loads and low noise are required, and are matched with them The gears are generally made of steel gears with good thermal conductivity.

We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: B18.5T-shaped head bolts, single-sided tooth washers, conversion bolts, slip-knot screws and other products, we can provide you with fastening suitable for you piece solution.

Hexagon socket end tightening

Customized Level 12.9


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].