Service HotlineShaft retaining ring (hereinafter referred to as retaining ring) is a very common part and is widely used in shaft parts. The existing solution for pressing the retaining ring is: place the retaining ring sleeve in the chamfering section or the guiding section of the shaft head, and then use an indenter whose inner hole diameter is larger than the diameter of the shaft head to press the retaining ring into the groove, and then press the retaining ring into the groove through the shaft head. The retaining ring is combined with the slot to prevent the indenter from continuing to move downward.
The traditional fixture shown in Figure 2 is composed of a hardened support cylinder and a hardened shear bar, and has a simple structure. The cylindrical pin is loaded into the hardened support cylinder, and the shear test is completed by applying an axial load to the hardened shear bar. Since the standard stipulates that the gap between the loading part and the supporting part does not exceed 0.15mm, in order to ensure the matching of the gap during the shear test of the cylindrical pin, the diameter of the cylindrical pin on the cylinder is generally equal to the theoretical cylindrical pin. In practical application, the cylindrical pin is irregular in size after heat treatment. To realize the shear test, the cylindrical pin must be inserted into the hole with the help of external force, which is difficult to install and clamp and takes a long time. If the double-sided shearing is performed, that is If the cylindrical pins need to be installed on both sides, the time is doubled, and the notch of the cylindrical pins cannot be guaranteed to face upwards.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a cement screw that is easy to install and can be removed in view of the shortcomings of the above-mentioned cement nails that cannot be disassembled and the expansion screws are not easy to install for the first time. Guangdong Yueluo Hardware Industry Co., Ltd. is a cement screw, which is realized by the following technical solutions. The cement screw is composed of a nail tip and a nail body. There is a thread at the back of the nail body. This thread can be an internal thread or an external thread. . When using, use a hammer to drive cement screws into the cement, and you can use ordinary screws or nuts to freely screw in and out to install and fix objects. Compared with the existing technology, Guangdong Yueluo Hardware Industry Co., Ltd. has the advantage that there are internal threads or external threads on the back of the cement screw, so it is not only easy to install for the first time, but also the objects to be installed can be disassembled repeatedly. Used as a fastener when installing objects on cement that may need to be dismantled.
Screws are one of the most common fasteners in people's work and life. Because of their simple structure and low manufacturing cost, they are deeply loved by people. In many positions that need to be tightened, people use screws as fasteners; general screws It consists of a screw and a nut. The screw is provided with an external thread. The nut is generally a regular hexagonal body, which is convenient for people to tighten or loosen the screw with a wrench or other tools.
The positioning pin is a pin designed to accurately position the two adjacent parts of the mold in a mold composed of two or more parts. It can be seen that the positioning pin plays a positioning role, and the mold must be accurately synchronized when it is closed. product, and the positioning pin can make the upper and lower molds play a role in accurate positioning. In the mold design and manufacture of Yueluo, the positioning pin is one of the most common parts. Since it is only used for positioning between parts, few people will pay too much attention to it. In the cold stamping process of Yueluo, the dimensional accuracy of the blanking parts depends on the size of the working part of the punch and the concave die, and the dimensional difference between them constitutes the blanking die gap. Gap is an important process parameter for die design, and its size has a great influence on the quality of the section of the blanking part, the blanking force, and the life of the die. If the gap is too large, punching burrs will appear in punching; if the gap is too small, secondary cracks will occur in the section and extrusion burrs will appear, which will make the quality of the section after punching unsatisfactory, and a reasonable gap will not only help the punching section. The improvement of quality also contributes to the improvement of the lifespan of the 9 bottles.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: Class A copper-plated stud bolts, Kabbah paper washers, anti-loose washers, lock washers and other products, we can provide you with suitable products for you. Fastener Solutions.
