Service HotlineThe main operation method of the embedded knurled copper nut of the lock nut is injection molding. After heating, it is embedded into the plastic part or directly injection molded. If injection molding is used, the melting point of P/NYLOY/PET is above 200°C. , After the embedded nut is hot melted into the plastic part, the temperature rises rapidly. After injection molding, the plastic body rapidly cools and crystallizes and hardens. If the embedded nut temperature is still at a high temperature, it may fall to the place where the copper nut contacts the plastic part. Start to loosen or crack. Therefore, copper nuts are used instead of carbon steel nuts in the injection molding of embedded nuts.
The rubber ring and the metal ring are integrally bonded and vulcanized. It is a sealing ring used to seal the thread and flange connection. The ring includes a metal ring and a rubber gasket. The metal ring is rust-proof, and the rubber ring is generally made of oil-resistant nitrile rubber or fluororubber. Combination pads are available in metric and inch sizes, and the standard JB982-77 specifies the combination of metal pads and rubber. Combination sealing washer is used for threaded pipe joints and screw plug sealing. It is generally used with ferrule type pipe joints to block oil ports. It is mainly used for end face static sealing of threaded joints of hydraulic valve pipe joints. It is suitable for British and American standards. Inch thread and end face static seal at French and German standard metric thread connections, etc. The combined sealing gasket can be divided into A type and B type according to the structure; it can be divided into full package and half package according to the difference of rubber.
Bolts made of high-strength steel, or bolts that require a large pre-tightening force, can be called high-strength bolts. High-strength bolts are mostly used for the connection of bridges, rails, high-voltage and ultra-high-voltage equipment. The fracture of this kind of bolt is mostly brittle fracture. High-strength bolts applied to ultra-high pressure equipment need to be prestressed to ensure the sealing of the container.
The working principle of the nut is to use the friction between the nut and the bolt for self-locking. However, the reliability of this self-locking is reduced under dynamic loads. In some important occasions, we will take some anti-loosening measures to ensure the reliability of the nut locking. Among them, the use of lock nuts is one of the anti-loosening measures. There are also two types of locking nuts. One is to use two identical nuts to screw on the same bolt, and a tightening torque is added between the two nuts to make the bolt connection reliable. The other is a special lock nut, which needs to be used together with a lock washer. As shown in FIG. 1, a plastic gasket 2 is arranged in the center of the nut 1 to play a locking effect, but the process is complicated and the production is inconvenient. One is to drill through threaded holes from the outer surface of the nut to the inner thread surface (usually 2, distributed at 90 on the outer surface), which are used to screw in small-diameter countersunk head screws. The purpose is to apply a thread to the thread. A centripetal force prevents the lock nut from loosening. At present, the lock nut with better quality on the market is inlaid with small copper pieces that are consistent with the thread of the lock nut on the inner surface of the nut, which is used to prevent the radial jacking screw from directly contacting the locked thread and being damaged. By. This kind of lock nut is gradually applied in the shaft end locking of rotating motion parts, such as the anti-looseness of the bearing at the mounting end of the ball screw. The process is equally complex.
Guangdong Yueluo Hardware Industry Co., Ltd. relates to a square nut fastener for cable bridge installation, which is characterized in that it includes an upper plate body and a U-shaped jacket, and the upper plate body is provided with a downwardly protruding connecting cylinder, The two side plates of the U-shaped jacket are connected to the connecting cylinder, and the center line of the two side plates is located on the center line in the length direction of the upper plate body; the bottom of the U-shaped jacket is a wave-shaped elastic plate, which is a wave-shaped elastic plate It is fixedly connected on the two side plates, and the space enclosed by the two side plates of the U-shaped jacket, the wave-shaped elastic plate and the bottom of the connecting cylinder is the installation position of the square nut. Guangdong Yueluo Hardware Industry Co., Ltd. has a simple and reasonable structure, and is extremely convenient and flexible to operate; it does not occupy the bottom space of the C-shaped steel after installation, which increases the variety of installation, and can be applied to square nuts of different thicknesses, and the installation is firm.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: plum blossom anti-theft screws, white M washers, hexagonal nuts with washers, flat head star bakelite screws and other products, we can provide you with suitable screws for you. Firmware Solutions.
