Service HotlineAt present, with the continuous growth of the demand for communication products, higher and higher requirements are put forward for the production capacity of equipment manufacturers, and at the same time, the requirements for the cost, weight and reliability of communication products are also more and more stringent. In order to facilitate the positioning of the equipment, pins are often used to complete the equipment, and a certain cost is incurred for its manufacture and assembly. In the past, such parts have been assembled in the form of threads. In order to ensure that the assembly height is within the specified range and to prevent loosening, bar turning is often used to form threads and positioning steps, and thread pinning glue is used in the assembly, and the cost of machining is relatively high. Large, more material waste. Based on the above drawbacks, in order to better solve this problem, some existing manufacturers use the interference fit riveting method, which solves the problem of material waste and anti-loosening, but the inner diameter of the pin hole and the outer diameter of the pin are matched. The machining accuracy of the machine is relatively high. Once the matching size is out of tolerance, a second matching is required, which wastes working hours and increases the slack time.
In the mechanical structure, the existing seals are used on the end face of the bolt or the end face of the oil joint. The copper washer is often used as the seal, and the copper washer can only be used once, and it will become hard after the second use, reducing its sealing performance. Especially when it is used on the oil drain bolt (also known as the oil drain plug) of the oil pan of the automobile engine, it is necessary to do a maintenance and replace a copper washer, otherwise it is easy to cause oil leakage. Even so, the wear of the screw hole of the engine oil pan is also very big. It is also difficult for ordinary auto repair shops to replace one copper washer at a time.
In the prior art, the hardware and the handle are generally assembled and connected by means of rivet riveting; in the process of assembling the hardware and the handle, the prior art adopts manual operation to realize the riveting and assembling process, which is time-consuming and labor-intensive. and low productivity.
Iron two combination screws can be sucked up with magnets, but stainless steel two combination screws are difficult to be sucked up. Environmentally friendly three-combination screws and non-environmentally friendly ones are invisible to the naked eye and require mechanical testing. It cannot be judged with the naked eye and out of thin air. The specifications of the two combination screws need to be determined by the national standard. The salt spray of the two combination screws needs to be measured with a salt spray machine for how many hours.
Although there are many types of self-tapping locking screws, they all have the following main characteristics: (1) Generally, they are made of carburized steel (accounting for 99% of the total products). Also available in stainless steel or non-ferrous metals. (2) The product must be heat treated. Carbon steel self-tapping screws must be carburized, and stainless steel self-tapping screws must be solution hardened. In order to make the self-tapping screw meet the mechanical properties and performance required by the standard. (3) The product has high surface hardness and good core toughness. That is, inner softness and outer rigidity. This is a major feature of the performance requirements of self-tapping screws. If the surface hardness is low, it cannot be screwed into the matrix; if the toughness of the core is poor, it will break as soon as it is screwed, and it cannot be used. Therefore, inner softness and outer rigidity are the requirements for self-tapping screws to meet the performance requirements. (4) The surface of the product needs surface protection treatment, generally electroplating treatment. Some product surfaces require phosphate treatment (phosphating). Such as: wall panel self-tapping screws are mostly phosphating. (5) It is produced by cold heading process. It is recommended to use high-speed cold heading machine and high-speed thread rolling machine or high-speed planetary thread rolling machine to ensure product quality. The self-tapping screw produced in this way has a well formed head and high thread quality.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: screws with washers, long double-headed screws with thin rods, copper columns for supporting copper columns, motherboard copper columns, spherical screws and other products, we can provide you with suitable products. Your fastener solution.
