Service HotlineMost of the capacitors on the market have two pins, which are the connection terminals of the positive and negative electrodes of the capacitor. At present, there is a big hidden danger in these capacitors, that is, the connection between the pins and the core inside the capacitor is basically a stick-on connection. When the capacitor is working, the internal temperature rises rapidly, and the stick-type connection is unstable after being heated, and it is easy to detach Or loose.
A: Metric Screws B: US Screws C: Inch Screws A: Metric Machine Screws: Metric Ex: M3 x 6 – PPB : M3 Machine Screws, 6mm Length, Cross, Flat Head, Black Plated. Finish Code: Finishing Specifications Head Code: The shape of the head. The shape of the screw head. Cylindrical head. Half head. sinking head. Spherical cylinder head. Pan head. Half round head. Hex Head.
rivet assembly device is provided with a base, the middle of the base is provided with a vertical groove, the bottom wall of the vertical groove extends forward and a horizontal convex block is suspended; the top surface of the convex block is fixed with a vertical rivet Needle and a guide column, the column body of the guide column is covered with a return spring; a downwardly open sliding block is mounted on the convex block, and the upper ends of the rivet needle and the guide column respectively protrude into the sliding block on the top wall of the sliding block. In the riveting pin hole and the guide hole, the inner wall of the riveting pin hole is provided with a large upper and a lower small horizontal step; the upper part of the bottom wall of the vertical groove is provided with a guiding limit rib. Guangdong Yueluo Hardware Industrial Co., Ltd. sets the rivet needle under the workpiece, and uses the upper die punch to press down the workpiece, and the rivet needle completes the operation of the rivet, omitting the operator to turn over and carry the rivet terminal board, thus effectively avoiding the rivet from The phenomenon that the rivet hole comes out. In addition, during operation, the workpiece is placed on the top surface of the slider, and the workpiece guide limit ribs and guide columns are used as shafts and radial limiters respectively. The riveting quality is good, and the purpose of saving time and labor and high efficiency is achieved.
On the other hand, especially in the aerospace field, the requirements for the sealing effect of screws are extremely strict, and the traditional screws are directly tightened when screwed into the workpiece or equipment, and the sealing effect is determined by the tightness, but due to the machining error of the workpiece or equipment The direct butt seal between the seals is difficult to achieve.
Subject content and scope of application This technical requirement specifies the technical requirements for the manufacture, installation and inspection of high-strength bolted joints of mobile machinery and equipment. Contents not specified in this technical requirement shall be implemented in accordance with relevant national standards. This technical requirement applies to mobile machinery steel structures that require high-strength bolted connections. This technical requirement applies to quality control and construction methods for in-plant and on-site installations. 2. Joint surface treatment 2.1 For friction type high-strength bolt connections, the joint surfaces at the joints are required to be in close contact with each other and have a sufficient friction coefficient. When the design drawing does not specify the treatment requirements for the joint surface, the treatment shall be carried out according to the following regulations: sandblasting or shot blasting the joint surface of high-strength bolts, remove impurities such as rust and oil stains on the surface, and reach the Sa2.5 standard , the roughness is 50 ~ 75μm, and the friction coefficient shall not be lower than 0.40. When there are regulations in the drawings, follow the regulations in the drawings. 2.2 The friction surface of the treated high-strength bolt connection should take protective measures to prevent contamination with dirt and oil. It is strictly forbidden to make any marks on the friction surface of the high-strength bolt connection. During storage in the factory, or during transportation, to the installation site, special precautions should be taken to prevent contamination of the connection surfaces. The installation unit should pay special attention to protecting the cleanliness and friction surface characteristics of the connecting plate of the high-strength bolt and the connecting surface of the parent body. It is not allowed to use a grinder to grind the connecting surface of the connecting plate and the connecting surface of the parent body. 3 Inspection of the anti-slip coefficient of the friction surface of high-strength bolts The inspection of the anti-slip coefficient should be based on the steel structure manufacturing batch, and each 2000t of a single project is regarded as a manufacturing batch, and those less than 2000t are regarded as a batch. When two or more surface treatment processes are selected, each surface treatment process needs to be inspected. Each batch of three groups of specimens. If the connection is diffused to an external enterprise, each corresponding enterprise shall conduct an anti-slip coefficient test. 3.1 The test piece used for the anti-slip coefficient test should be processed by the factory or the diffusion enterprise. The test piece and the representative steel structure member should be of the same material, produced in the same batch, using the same friction surface treatment process and have the same surface state. And use the same batch of high-strength bolt connection pairs of the same performance level and store them under the same environmental conditions. The anti-slip coefficient test is carried out according to the test method of GB50205 Code for Acceptance of Construction Quality of Steel Structure Engineering. 3.2 The minimum value of the anti-slip coefficient inspection must be equal to or greater than the design specified value. When the above specified values are not met, the friction surface of the component should be reprocessed. The friction surface of the treated component is re-inspected. 4. Connection and installation of friction type high-strength bolts for steel structures 4.1 Preparations before installation 4.2 Select qualified bolts, nuts and washers. The guarantee period for the torque coefficient of the connecting pair is six months from the date of delivery. 4.3 Bolts, nuts and washers in the following cases are unqualified products and are prohibited from being used. a. The source (manufacturer) is unknown; b. The mechanical properties are unknown; c. The torque coefficient k is unknown; d. Defective; e. No performance test report attached; f. Mixed with other batches of bolts; g. Bolts with insufficient length, that is, the bolt head does not show the end face of the nut after tightening. Generally, the length of the end face of the nut to be taken out is 2 to 3 threads. h. The torque coefficient of the connecting pair exceeds the warranty period. Special attention should be paid to waterproofing during transportation and storage. 4.4 Before the construction of the large hexagonal head high-strength bolts, the torque coefficient of the high-strength bolt connection pair should be re-inspected according to the factory approval. Each batch of 8 sets should be re-inspected. Less than or equal to 0.010. The re-inspection method of the torque coefficient shall be carried out in accordance with the provisions of GB50205 Code for Acceptance of Construction Quality of Steel Structure Engineering. The installation of high-strength bolts should be carried out within a short period of time after the test.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: protective cover decorative dust cover, centering pins for sub-shafts, large cap nails GB109 flat head rivets, enlarged and thickened gaskets and other products , we can provide you with a fastener solution that suits you.
