Service HotlineEarless retaining ring (known as Constant Section Rings abroad) is also called constant section retaining ring, because the cross section is equal, and there is no ear part protruding from the traditional stamping retaining ring, so it is called earless retaining ring. Earless retaining ring and spiral retaining ring have similarities in production, processing and use characteristics. They are both flattened and wound by steel wire. After heat treatment and surface treatment, they have good elasticity and toughness. Earless retaining ring is divided into two types: shaft use and hole use, and there are various forms of tail ends to choose from. The application of earless retaining ring is the same as that of traditional C-type retaining ring, which is widely used in hydraulic parts assembly, valves, instruments, various lock core components, needle roller bearings, pulleys, connectors, quick connectors and other mechanical assemblies.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a flat gasket that improves the lubrication performance of the contact surface and reduces the friction of the contact surface. Yueluo is implemented through the following technical solutions: a flat gasket with straight upper and lower end faces, characterized in that: the upper and lower end faces are dotted with pits, the pits are spherical pits, and the pit diameter is 2-3mm , the pit depth is between 0.5-lmm. The bottoms of some of the pits are provided with through holes penetrating the upper and lower end faces, and the diameter of the through holes is not greater than 0.5mm. The flat gaskets provided by Yueluo have pits with reasonable design parameters on the upper and lower end faces of the flat gaskets. The pits can store oil, so the lubrication of the contact surfaces of the gaskets can be well improved. It can effectively reduce the friction of the contact surface of the gasket and reduce the failure rate; in addition, the design of the through hole enables a smooth oil passage between the upper and lower end faces of the gasket, ensuring that the upper and lower end faces can be well lubricated.
T-bolt with a spring, used for undercutting the opening of the outer closed cavity, including a head and a rod part connected in one piece, and also including a strip spacer, a spring and a pull rod, and the length of the strip spacer is greater than The opening, the connecting part of the head and the rod part are set as polygonal anti-rotation blocks, and the strip-shaped spacer is provided with anti-rotation holes for inserting the anti-rotation blocks, and the shape and size of the anti-rotation holes are the same as The size of the anti-rotation hole is smaller than that of the head; the spring is threadedly matched with the rod part, and is fixedly connected with the pull rod, and the pull rod moves away from the rod part along the axial direction of the rod part One side of the head extends. The utility model can be easily and reliably buckled in the opening of the airtight cavity, thereby facilitating the installation and connection of external parts.
At present, in the standard cabinets of computers, networks, automation, etc., to fix the equipment in the cabinet, it needs to be fixed by using fasteners. The nuts in the existing fasteners are ordinary nuts, which are internal card structures. , there are the following shortcomings: 1. The installation and disassembly are complicated, and a large amount of force is required to insert the nut during installation and disassembly, and the nut cannot be installed and disassembled at all due to the processing error of each nut; 2. After the nut is used for a long time, the nut The card edge will have slack problem, which will affect the use; 3. Installation or disassembly is easy to cause problems such as falling, which may cause electrical short circuit, etc., and there are potential safety hazards; 4. The efficiency of equipment installation is low.
Generally, the bolts or nuts used to press workpieces or fixtures in the T-slot of the machine tool table are made into square or rectangle. Things are very inconvenient.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: blue and white flat washers, set full pan head screws, bearing washers, GB6170 nuts and other products, we can provide you with suitable fastening products piece solution.
