Service HotlineThe quality of electroplating is measured primarily by its corrosion resistance, followed by appearance. Corrosion resistance is to imitate the working environment of the product, set it as the test condition, and perform a corrosion test on it. The quality of electroplating products shall be controlled from the following aspects: 1. Appearance: Partial uncoated, scorched, rough, gray, peeling, crusted, and obvious stripes are not allowed on the surface of the product, and pinholes, pitting, and black plating are not allowed. Slag, loose passivation film, cracks, peeling off and serious passivation marks. 2. Coating thickness: The operating life of fasteners in corrosive atmosphere is proportional to its coating thickness. The general recommended thickness of economical electroplating coating is 0.00015in ~ 0.0005in (4 ~ 12um). Hot-dip galvanizing: the standard average thickness is 54 um (43 um for diameter ≤ 3/8), and the minimum thickness is 43 um (37 um for diameter ≤ 3/8). 3. Coating distribution: With different deposition methods, the aggregation method of the coating on the surface of the fastener is also different. During electroplating, the coating metal is not uniformly deposited on the peripheral edge, and a thicker coating is obtained at the corners. In the threaded portion of the fastener, the thickest coating is located on the thread crest, gradually thinning along the flank of the thread, and the thinnest deposit is at the bottom of the thread, while hot dip galvanizing is just the opposite, the thicker coating is deposited on the inside corners and On the bottom of the thread, mechanical plating tends to deposit the same metal as hot-dip plating, but is smoother and has a much more uniform thickness over the entire surface [3]. 4. Hydrogen embrittlement: During the processing and processing of fasteners, especially in the pickling and alkali washing before plating and the subsequent electroplating process, the surface absorbs hydrogen atoms, and the deposited metal coating then traps hydrogen. When the fastener is tightened, the hydrogen is transferred towards the most stressed parts, causing the pressure to build up beyond the strength of the base metal and producing microscopic surface cracks. Hydrogen is particularly active and quickly seeps into the newly formed fissures. This pressure-rupture-penetration cycle continues until the fastener breaks. Usually occurs within a few hours after the first stress application. To eliminate the threat of hydrogen embrittlement, fasteners are heated and baked as soon as possible after plating to allow hydrogen to seep out of the plating, typically at 375-4000F (176-190C) for 3-24 hours. Since mechanical galvanizing is non-electrolyte, this virtually eliminates the threat of hydrogen embrittlement, which exists in galvanizing using electrochemical methods. In addition, due to engineering standards, it is forbidden to hot-dip galvanize fasteners with hardness higher than HRC35 (Imperial Gr8, metric 10.9 and above). Therefore, hydrogen embrittlement rarely occurs in hot-dip plated fasteners. 5. Adhesion: Cut or pry off with a solid tip and considerable pressure. If, in front of the blade tip, the coating peels off in flakes or skins, exposing the base metal, the adhesion shall be considered insufficient.
The existing adjusting screw is generally composed of a screw and a nut on the top of the screw. The screw is driven to rotate by means of a screwdriver, and then the screw is driven to rotate. In and out, adjusting other objects connected to it and changing position accordingly.
Bolt and nut fasteners are widely used fasteners, which can be used in mechanical products as well as daily craft industrial products, such as plastic packaging boxes, plastic packaging boxes, paper packaging boxes, paper packaging boxes, etc. . When bolt and nut fasteners are used in daily craft industrial products, the requirements for the degree of tightening are generally low, but they are required to be easy to install and use. When assembling the existing bolt and nut fasteners, it is generally necessary to manually twist the bolt or the nut several times until the two are tightened, which takes time and causes inconvenience in daily life. Lower, it is manifested as an increase in labor costs. SUMMARY OF THE INVENTION The main purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a bolt and nut fastener that is easy to install in view of the above-mentioned deficiencies of the prior art. The two are assembled and fastened, which is convenient to use.
The existing spring screw includes a screw rod, a spring connecting sleeve, a spring, a fixed connecting sleeve, a nut and a nut sleeve, wherein the screw rod includes a screw cap, a connecting section without threads and a threaded connecting section with threads, and the connecting section is located in the screw cap and the thread. A shaft shoulder is arranged between the connecting sections and between the connecting section and the threaded connecting section, the connecting section of the screw is sleeved with a spring connecting sleeve, a spring and a fixed connecting sleeve, the spring connecting sleeve is close to the screw cap, and the connecting sleeve is connected between the spring connecting sleeve and the fixed connecting sleeve The connection spring is connected with a threaded nut on the threaded connection section of the screw, and the nut sleeve is connected to the nut sleeve. The fixed connection sleeve is fixedly connected to the upper die of the steel mold through bolts, and the nut sleeve is welded to the lower mold of the steel mold. When clamping the mold, a professional is required to turn the screw from the lower mold to the upper mold or hook it to the upper mold with a foot and then tighten it with the wind, which is inconvenient to install, has low work efficiency, and has potential safety hazards. Contents of the utility model Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. aims to provide a spring screw that is easy to operate. In order to solve the problems existing in the background technology, Guangdong Yueluo Hardware Industry Co., Ltd. adopts the following technical scheme: a spring screw, including a screw rod, an upper compression spring washer, a spring, a fixed sleeve, a lower compression spring washer, Base and fixing nut. The screw rod includes a screw cap, a connecting section without threads and a threaded connecting section with threads, the connecting section is located between the screw cap and the threaded connecting section, and a shaft shoulder is arranged between the connecting section and the threaded connecting section. The connecting section of the screw rod is sleeved with an upper compression spring washer, a spring, a fixing sleeve, a lower compression spring washer and a base, and the threaded connection section is connected with a fixing nut. A fixed sleeve is sleeved between the connection section and the threaded connection section, and the fixed sleeve is sleeved with a lower pressure spring washer and a base. The upper compression spring washer is close to the screw cap, the lower compression spring washer is fixed on the base by four screws, the spring is placed between the upper compression spring washer and the lower compression spring washer, and one end of the spring is sleeved with the upper compression spring washer , and the other end is sleeved with a fixed sleeve. For Yueluo, the diameter of the spring screw is between T20-T27. In this preferred solution, the use performance of the spring is high, which is beneficial to prolong the service life of the spring screw. For Yueluo, preferably, the thread connecting section of the screw adopts T-shaped thread. In this preferred solution, the fixing nut is tightly matched with the threaded connection section, so that the steel mold is clamped tightly. Yueluo is preferably made of 40Cr material for the fixing nut and screw. In this preferred solution, the rigidity of the fixing nut and the screw rod is high, which is beneficial to improve the usability of the spring screw. Yueluo is preferred, the spring screw parts except the fixing nut and the screw rod are made of 47# steel material. In this preferred solution, the production cost is low. In summary, Guangdong Yueluo Hardware Industry Co., Ltd. brings the beneficial effects: when the spring screw is used, it is only necessary to use a wrench to move the fixed nut, which is convenient for installation, disassembly and replacement, improving work efficiency and reducing production costs.
Self-tapping screw is a kind of threaded fastener that self-tapping and drilling the matching female thread in the pre-drilled hole of metal or non-metal material. When using self-tapping screw, a flat washer is often required to protect the fastening surface. Traditional When the self-tapping screw is used, the flat pad is easy to fall off, resulting in low work efficiency. In view of this, we propose a combined structure of the stuck self-tapping screw spring washer that prevents the flat pad from falling off.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: professional manufacturing, round hole ABS copper columns, accessories pins, orthodontic screw caps and other products, we can provide you with suitable screws for you. Firmware Solutions.
