Service HotlineGenerally speaking, the metal plate needs to open holes for inserting the rivets, and then press the two sides of the metal plate along the positive direction of the metal plate with a jig, so that the metal plate is deformed in the plane direction, which makes the inner edge of the hole Shrink and fit the rivet. Existing riveting techniques are not suitable for thin sheets. Because the thin plate does not have enough thickness to compress in its forward direction, the insufficient deformation in the forward direction causes enough deformation in the plane direction to insert the rivet, so the rivet cannot be firmly fixed to the thin plate.
Head type broadcast 1. Hexagon head (hexagon head) 2. Hexagon head with flange (hexagon head with flange) 3. Square head (square head) 4. T head T head (hammer head) 5. Mushroom head (truss head) 6. Cheese head 7. Round head 8. Pan head 9. Countersunk head (flat head) 10. Raised countersunk head (oval
The utility model proposes an installation structure which adopts a T-shaped bolt to cooperate with a channel, which includes a bolt head, an installation channel, a nut and a washer. The upper end of the screw rod is provided with a screw head, the two side walls of the bolt head are respectively provided with an arc surface, the two ends of the bolt head are provided with protrusions, and the interior of the installation channel is provided with an inner cavity, There is an opening above the installation channel, the bolt head is installed in the inner cavity, the nut is installed on the screw, the nut is located above the installation channel, and the gasket is installed on the installation channel and the nut between.
Code name and standard number of inch thread commonly used abroad Mark code name country and standard number Remarks BSW standard Wyeth coarse thread series, general purpose cylindrical thread British standard BS 84 inch thread with a profile angle of 55° BSF standard Wyeth fine thread series, General Purpose Cylindrical Thread Whit.S Additional Whit.S Optional Series, General Purpose Cylindrical Thread Whit Non-standard thread with Whitworth profile UN Uniform thread of constant pitch series American standard ANSI B1.1 inch thread with 60° profile angle, with Internal and external threads with standard profile (flat or rounded at random) UNC Coarse thread unified thread UNF fine thread unified thread UNEF superfine thread unified thread UNS① Special series unified thread UNR round The uniform thread profile angle of the arc root constant pitch series is 60° inch thread, UNR, UNRC, UNRF, UNREF, UNRS with arc root are only used for external thread without internal thread UNRC arc root coarse thread Series Unified Thread UNRF Circular Root Fine Thread Series Unified Thread UNREF Circular Root Ultra Fine Thread Series Unified Thread UNRS Circular Root Special Series Unified Thread NPT② Generally used for pipe thread American standard ANSI B1.20.1 Profile angle is 60° Inch Pipe Thread NPSC Pipe Fitting Straight Pipe NPTR Pilot Connection Tapered Pipe NPSM Mechanical Connection Straight Pipe NPSL Lock Nut Straight Pipe NPSH Hose Connection Straight Pipe NPTF Dry Seal Standard Tapered Pipe Thread American Standard ANSI B1.20.3 Type I PTF-SAE SHORT Dry Seal Short Taper Pipe Thread Type II NPSF Dry Seal Standard Fuel Oil Straight Pipe Internal Thread III Type NPS1 Dry Seal Standard General Straight Pipe Internal Thread IV Type ACME③ General Purpose Trapezoid Thread American standard ANSI B1.5 Inch drive thread with 29° profile angle ① Dimensions and tolerances All diameter and pitch combinations other than the standard series are calculated using the same formula as the standard series. ② my country's 60° conical pipe thread GB/T12716-1991 is equivalent to it. ③ACME thread includes two kinds of matching trapezoidal threads, general purpose and centering, of which the general purpose thread has the same performance as the trapezoidal thread specified in my country's standard GB/T5796-1986.
screw can be equipped with only one spring washer or only one flat washer, or it can also only be equipped with a two-piece combination of flower teeth. The national standard number of the combination screw is represented by GB9074. The commonly used cross recessed small pan head three combination screw national standard is GB9074.8.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: cylindrical screws, straight thread screws, metal spring flat washers, chamfered hexagon socket screws and other products, we can provide you with fastening suitable for you piece solution.
