Service HotlineExisting bolt pairs usually include bolts, nuts and washers, and their specific structures and usage methods are traditionally known and common in life. They will not be described in detail here. You can find relevant bolt pairs by searching for bolt pairs on the Internet. Information picture, the structure of the ordinary bolt pair has basically no structural improvement since it was used as a fastener. The production requirements of ordinary bolt pairs are the basic material, structural strength, and accuracy requirements, while the tightening and anti-loosening requirements The requirements of the effect are basically to achieve the problem of tightening and anti-loosening by using elastic washers, anti-loosening washers or using double nuts.
As we all know, whether it is the necessities in people's life or the equipment in industrial production, there will be a structure of screws and screw holes on it. This kind of structure that can simply fix some components together has been widely used in various fields. For the installation and removal of screws, people invented manual screwdrivers, and then to electric screwdrivers and so on. For manual screwdrivers, the operator needs to manually install or remove the screws. When encountering small screws, it can still handle it. When encountering large screws, due to people's limited strength, they may not install the screws in place, so it was invented. Electric screw. When installing the screw, which is widely used in the market, the operator needs to hold the screw handle, fix the screw on the screw port, and then align the screw with the corresponding screw hole for screwing. The disadvantage of this kind of screw is that it is heavy in quality and laborious to operate, and secondly, the operator will be injured due to operating errors, and the consequences are extremely serious. In view of this deficiency, people fix the screws on a work frame, so that before installing the screws, the operator only needs to adjust the screws to the designated position, and then the screws can be installed, which is convenient and simple. However, there are still potential safety hazards. In the process of adjusting the screw, it is still possible that the power of the screw may be turned on by mistake due to operating errors, resulting in injury to the operator. In view of the above-mentioned defects, it is necessary to invent a screw installation method with an anti-missing function.
At present, with the continuous growth of the demand for communication products, higher and higher requirements are put forward for the production capacity of equipment manufacturers, and at the same time, the requirements for the cost, weight and reliability of communication products are also more and more stringent. In order to facilitate the positioning of the equipment, pins are often used to complete the equipment, and a certain cost is incurred for its manufacture and assembly. In the past, such parts have been assembled in the form of threads. In order to ensure that the assembly height is within the specified range and to prevent loosening, bar turning is often used to form threads and positioning steps, and thread pinning glue is used in the assembly, and the cost of machining is relatively high. Large, more material waste. Based on the above drawbacks, in order to better solve this problem, some existing manufacturers use the interference fit riveting method, which solves the problem of material waste and anti-loosening, but the inner diameter of the pin hole and the outer diameter of the pin are matched. The machining accuracy of the machine is relatively high. Once the matching size is out of tolerance, a second matching is required, which wastes working hours and increases the slack time.
rivet is a nail-shaped object used to join two parts or components with a through hole and a cap on one end. In riveting, the riveted parts are connected by their own deformation or interference. There are many types of rivets, and they are not limited to the form. The existing switch is not easy to fix, and needs to be supported by others during installation, which leads to waste of labor, and at the same time, it is easy to damage the hands of the supporting personnel. The existing device driving method is relatively laborious. Some devices require rivets of different lengths in different thicknesses, and cannot be assembled by themselves of the same type.
hand screw is a screw with a plastic head, and the user fixes the hand screw by turning the plastic head by hand. At present, a hand screw is disclosed in the market publication number CN202203253U, which includes a plastic head and a screw rod, the plastic head and the screw rod are connected together, and the height of the plastic head is higher than that of an ordinary screw, and the height is 12 cm. The screw of the hand screw is fixed in the plastic head by glue. After a period of use, the aging of the glue leads to the loosening of the screw and the plastic head. When the plastic head is stressed, the screw rod comes out of the plastic head, which affects the normal use of the hand screw.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: acrylic bolts, thin head bolts, T-nuts, built-in tension bolts and other products, we can provide you with suitable fastener solutions for you Program.
