Service Hotlineflat washer, an annular groove is formed on the outer side of the upper surface of the flat washer, and a sealing ring is embedded in the annular groove, at least five circularly equidistantly arranged cylinders are fixed on the upper surface of the flat washer, and the The upper surface of the flat washer is provided with a circular hole that communicates with its bottom, a collar is arranged in the circular hole, an upper circular ring is fixed above the collar, a lower circular ring is fixed below the collar, and the upper circular The diameter of the ring is the same as the diameter of the lower ring, the diameter of the collar is smaller than the diameter of the upper ring, the diameter of the collar is consistent with the diameter of the circular hole, and there are at least three equally spaced holes in the middle of the outer wall of the flat washer. A circular groove, the outer wall of the flat washer is fixed with at least three reinforcing blocks staggered with the circular groove, and the reinforcing blocks and the flat washer are welded into one piece.
Embodiments of Guangdong Yueluo Hardware Industry Co., Ltd. are described in detail below, examples of which are shown in the accompanying drawings, wherein the same or similar reference numerals represent the same or similar elements or elements with the same or similar functions throughout. The embodiments described below by referring to the accompanying drawings are exemplary, and are intended to be used to explain Guangdong Yueluo Hardware Industry Co., Ltd., and should not be construed as a limitation to Guangdong Yueluo Hardware Industry Co., Ltd.
At present, with the continuous growth of the demand for communication products, higher and higher requirements are put forward for the production capacity of equipment manufacturers, and at the same time, the requirements for the cost, weight and reliability of communication products are also more and more stringent. In order to facilitate the positioning of the equipment, pins are often used to complete the equipment, and a certain cost is incurred for its manufacture and assembly. In the past, such parts have been assembled in the form of threads. In order to ensure that the assembly height is within the specified range and to prevent loosening, bar turning is often used to form threads and positioning steps, and thread pinning glue is used in the assembly, and the cost of machining is relatively high. Large, more material waste. Based on the above drawbacks, in order to better solve this problem, some existing manufacturers use the interference fit riveting method, which solves the problem of material waste and anti-loosening, but the inner diameter of the pin hole and the outer diameter of the pin are matched. The machining accuracy of the machine is relatively high. Once the matching size is out of tolerance, a second matching is required, which wastes working hours and increases the slack time.
At present, during assembly of many pin installation mechanisms, the pins need to be installed into the holes or arranged in an orderly manner, and there are many problems in this assembly method. First of all, during assembly, if the hole diameter of the hole product is large, when the pin enters the hole of the hole product, part of the pin entering the hole of the hole product is not fixed, which often leads to slight deviation. In addition, this assembly method is usually only suitable for parts with large apertures and small depths, and when installing multiple pins, it is impossible to automatically install all pins in place due to space constraints. Special tools need to be made for installation operations, and it is easy to cause pins. damage.
structure for concealing installation screws, comprising a locking piece, a driving piece, a bottom plate, a blocking cover and a handle head, the lower ends of the two locking pieces are provided with positioning holes, and the locking pieces pass through the positioning holes and the locking piece positioning posts on the base Snap and fix, the middle of the two locking pieces is provided with a protruding point, the movable groove of the driving piece corresponds to the protruding point of the nine locking pieces for fixing, the riveting point holes and screw holes of the bottom plate and the riveting points of the base The position that matches the screw holes and is fixed by screws, the blocking cover is directly inserted into the bottom plate, and the blocking cover is fixed by the rotating drive piece, the handle head is inserted into the base, and the slot of the handle head moves to the locking piece at the locking piece Lock the handle.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat head hexagon socket head cap screws, shrimp tail nuts, detachable organizer boxes, black small flat washers and other products, we can provide you with suitable products for you Fastener Solutions.
