Service HotlineThe purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to overcome the above shortcomings and provide a limit screw. The technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. is realized in the following way. Its structure is composed of screws, hexagonal copper posts and limit necks. The left end of the limit neck is open, the hexagonal copper column is communicated with the inside of the limit neck, and the inside is provided with screw threads. The design length of the screw thread in the hexagonal copper column is 1/3-2/3 of its own length. The advantages of Guangdong Yueluo Hardware Industry Co., Ltd. are (12), which can effectively prevent the problem of poor memory contact caused by the increase in the deformation of the motherboard due to the warping and deformation of the motherboard during installation and fixing, and can effectively control the deformation. effect.
Nuts and washers are both small and medium-sized components of the tension reinforcement system, and they are easily lost on the construction site when used separately, which is not conducive to the storage management of turnover materials; 3) During the process of formwork support and removal, they must be installed individually And demolition, thus adding a construction process, affecting the efficiency of construction.
In the prior art, spring pads are fixed to the seat pan or to the height adjuster tube. However, in the absence of a seat pan, additional components are required to secure the spring pads to prevent movement of the spring pads in the longitudinal direction of the vehicle. FIG. 1 shows such a seat spring pad 2 , which is fixed to the seat pad 1 by means of additional fixing parts 4 . Additional weight is added due to the use of additional fixing parts and a separate step is required in the assembly process to connect the fixing parts to the spring pads. During use, there may be noise between the spring cushion and the seat cushion
Knurled copper nuts are widely used in the following fields: notebook computer plastic casing, desktop computer plastic casing, GPS plastic casing, router plastic casing, mobile phone plastic casing, infinite communication facility plastic casing, home appliance plastic casing, automobile, electrical appliances, medical, electronics, etc. plastic shell.
Usually, the forming of the bolt head adopts cold heading plastic processing. Compared with the cutting process, the metal fiber (metal wire) is continuous along the shape of the product, and there is no cut in the middle, thus improving the strength of the product, especially the mechanical properties. The cold heading forming process includes cutting and forming, single-station single-click, double-click cold heading and multi-station automatic cold heading. An automatic cold heading machine performs multi-station processes such as stamping, heading forging, extrusion and diameter reduction in several forming dies. The processing characteristics of the original blank used by the single-station or multi-station automatic cold heading machine are determined by the size of the bar with a length of 5-6 meters or the wire rod with a weight of 1900-2000KG, that is, the characteristics of the processing technology. The point is that cold heading does not use pre-cut single blanks, but uses the automatic cold heading machine itself to cut and upset (if necessary) blanks from bars and wire rods. Before extruding the cavity, the blank must be shaped. A blank that meets the technological requirements can be obtained by shaping. Before upsetting, reducing and positive extrusion, the blank does not need to be shaped. After the blank is cut, it is sent to the upsetting and shaping station. This station can improve the quality of the blank, reduce the forming force of the next station by 15-17%, and prolong the life of the die, and the bolts can be made with multiple diameter reductions. The precision that can be achieved by cold heading is also related to the selection of the forming method and the procedure used. In addition, it also depends on the structural characteristics of the equipment used, the process characteristics and its state, the precision of the tool and die, the life and the degree of wear. For high-alloy steel used in cold heading forming and extrusion, the roughness of the working surface of the cemented carbide mold should not be greater than Ra=0.2um. When the roughness of the working surface of this type of mold reaches Ra=0.025-0.050um, it has the highest life.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: dome head screws with washers, solid wood screws without through holes, ISO2338 cylindrical pins, cross combination bolts in the cavity and other products, we can provide you with suitable products for you. Fastener Solutions.
