Service HotlineThe purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to overcome the above-mentioned shortcomings of the prior art, and provide a hidden screw fastener, which avoids the defect that the screw end cap is directly exposed when the traditional screw is tightened, which affects the appearance. Washers and shields hide the end caps of the screws, which are both beautiful and insulating, preventing the screws from rusting, and avoiding scratches due to burrs on the ends of the screws, which are not only beautiful but also practical and safe.
In order to solve the problem of nut loosening, various self-locking nuts have appeared, which have complex structure, high production cost, inconvenient installation and unsatisfactory anti-loosening effect. At present, the never-loosening nuts produced in Japan are mostly used, mainly in the form of double nuts. Each nut is provided with an eccentric cam protrusion, and each nut is provided with a groove and an inclined plane to squeeze the cam protrusion of each nut. When pressing, the cam protrusion of the nut will move to a small radius along the slope of the nut, so that the nut will not loosen, but whether it is a nut or a nut, it is always under the action of eccentric force. In addition, various non-loose nuts designed by many manufacturers are to increase the friction between the nut and the fastening workpiece or increase the barb to achieve the purpose of never loosening, but the effect is not ideal.
Referring to Figure 1, one end of the existing insert nut 1' is embedded in the injection molded part 2', and the other end is exposed to the injection molded part 2'. The insert nut 1' has opposite lower and upper end surfaces in the axial direction. The end face of one end of the insert injection molded part 2' is the lower end face. In order to reduce the resistance during hot pressing, the connection between the inner wall surface and the lower end surface of the insert nut 1 ′ is provided with an inclined surface. However, when the embedded nut 1' of this structure is hot-pressed, the hot melted glue will generate a shunt that rises along the slope, and then a convex peak is formed in the screw hole of the embedded nut 1', and the convex peak occupies the screw. The space in the hole prevents the screw 5' from being completely screwed in; at the same time, due to the shunting of the hot solder, the knurling of the inner nut 1' near the upper end face cannot be filled with the solder, which makes the inner nut 1' and the inner nut 1' and The injection part 2' is not firmly embedded. Therefore, the locking strength of the existing insert nut 1 ′ and the screw 5 ′ after being hot-pressed is relatively low.
The motor bearing retaining ring is used to fix the axial position of the bearing. The structure of the bearing retaining ring 1 in the prior art is shown in FIG. 1 , which is a ring-shaped sheet-like structure with a gap, the inner diameter of which is smaller than the inner diameter of the connected bearing, and the outer side 11 of the ring is a continuous arc shape. The inner side of the ring is provided with a groove 12, 13 of the same size on both sides of the midpoint of the ring, and the width of the groove is equal to the distance from the groove to the gap of the ring. When the axial locking force (impact) of the bearing retaining ring of this structure is greater than 6.5N, serious deformation will occur or even the retaining ring will be separated from the shaft shoulder. In order to solve this problem, when the axial locking force is greater than 6.5N, the prior art generally adopts a two-ring combined structure of steel wire ring + bearing retaining ring, and its installation state is shown in Figure 2, as shown in Figure 2, l It is a bearing retaining ring in the prior art, 3 is a locking nut, 4 is a fan blade insert, 5 is a bearing, 6 is a shaft, and 7 is a wire ring. However, such a structure is costly and troublesome to assemble, especially if the bearing retaining ring is not placed in place during assembly, the bearing retaining ring is at risk of being crushed.
Fig. 1, Fig. 2, and Fig. 3 show that the rivet nut is cut into the required blank from a chemically treated low carbon steel disc, and the blank is placed in the die, and the upper and lower punches are used for shaping to obtain a shaped blank. , and then put the shaped blank in the die, use the punch punch to cold-head out the required brim blank (1) and the deformed skirt (2), and then use the punch punch in the die to continue Cold heading out the brim blank (1) and the deformed skirt (2). Then put the semi-finished material into the concave die and use the punch of the punch to continue to squeeze the threaded hole (3) of the nut tapping skirt, and then put the semi-finished blank into the concave die and use the upper punch and the lower sleeve to drop it. material. There are fish teeth (6) below the brim; the outer side of the lower end of the threaded hole is provided with a chamfer (5); the cross-section of the thread of the inner wall of the threaded hole is an isosceles trapezoid, and the upper bottom of the trapezoid is a concave arc (4), In this way, the riveted object is firmly connected to the rivet nut.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: chemical anchor bolts, flat head small countersunk head half hexagonal rivet nuts, tapping expansion bolts, DIN6796 and other products, we can provide you with suitable products Your fastener solution.
