Service HotlineMany existing products need to use screws in the production process, especially in the field of nuclear power sluice gates, it is necessary to fill a part of the sluice gate with screws to fix the size and structure. If the fixing effect is not good, then It will lead to more leakage of water gates, waste a lot of water resources, and even cause safety accidents.
The global economy continues to slump and overseas export trade is sluggish. Many fastener companies at home and abroad are facing severe tests. Accelerating economic transformation and structural upgrading is imminent, and developing overseas markets is undoubtedly an important way out for the development of the current fastener industry. From the fourth quarter of 2011 to the first half of 2012, affected by the objective environment, the development speed of the fastener industry may slow down, but from the third quarter of 2012, with the policy in place, the convening of the 18th National Congress of The upcoming series of development policies, etc., can promote the further development of the industry. And we must insist on innovation and adjustment and transformation, we must continue to rely closely on key industries such as automobiles, new energy, aerospace, shipbuilding, urban transportation, IT, electronic appliances, construction, etc., accelerate the optimization and upgrading of fastener products, and promote fasteners. The whole industry develops healthily and steadily. The global fastener market size exceeds 50 billion US dollars, and China's total fastener production in 2012 is also expected to reach about 6.8 million tons. However, compared with the manufacturing powerhouses such as the United States and Japan, there is still a big gap in my country's fastener industry.
In the process of electronic accessories such as mobile phones and computers, especially multi-layer circuit boards, there are generally fixed connections between multi-layer circuit boards or other components. At present, there are two main connection methods. One is to use laser welding. However, the laser welding equipment is expensive and has very high requirements on the position of the weldment. Therefore, during welding, it must be ensured that the final position of the weldment needs to be the same as the laser beam will impact. Solder joint alignment. The other is to use a metal rivet to pass through the positioning hole, and then impact the rivet with a punching needle, so that the open end of the rivet is deformed and opened and pressed on the fixed piece to form a rivet fixed state. However, in actual operation, when the open end of the rivet tube is opened and deformed by the impact, strong cracking often occurs, resulting in a small amount of conductive fracture debris, which falls on the circuit board or other devices to be connected, causing Short circuit, in view of this shortcoming, some manufacturers have changed the metal rivets to plastic materials, but the plastic rivets have poor ductility and often break when impacted with a punching needle, resulting in the failure to achieve the riveting fixing force of the original metal rivets. In addition, the above two fixing methods are complicated in operation and low in installation efficiency.
The circlip is also called a retaining ring or a retaining ring. It is a kind of fastener and is installed in the shaft groove or hole groove of the machine and equipment to prevent the axial movement of the parts on the shaft or hole. The circlip includes an arc-shaped elastic bending portion and a circlip protrusion at the end of the elastic curved portion, and the circlip protrusion is provided with a small hole for matching with needle-nose pliers or circlip pliers. This part is a commonly used part on the equipment. Once the assembly is not in place, it will affect the overall performance of the equipment and cause safety hazards. At present, the most common assembly method is to manually clamp and deform the circlip with circlip pliers or needle-nose pliers, put the circlip into the annular groove of the inner hole of the end cover, and then release the needle-nose pliers or circlip pliers. . The assembly of the circlip is very troublesome, labor-intensive, and has low assembly efficiency. Once mass production is required, this process often becomes a bottleneck restricting production.
screw is a tool that uses the physical and mathematical principles of the circular rotation and friction of an object to fasten the mechanism of the object step by step. When using screws to fasten objects and parts, it is often necessary to use screws with spring washers and flat washers to lock and fix the relative position, so as to improve the stability of the fastening connection and make the screws less prone to loosening. However, in the prior art, the method of manually inserting the spring washer and the flat washer in sequence is generally used, which not only increases the workload of the staff, but also makes the installation efficiency relatively low. On the other hand, the traditional screw with a gasket only has the function of fixing, Without the function of sealing, it cannot be applied to special equipment such as oil tanks and airtight cabins. Therefore, it is necessary to design a screw that can reduce the workload and have its own sealing structure.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hexagonal flange nuts with pads, hollow rivets, national standard aluminum profile square slider, square T slider aluminum nut, flange cross bolt and other products, we can provide you with fastener solutions that are suitable for you.
