Service Hotline[In a preferred example of Guangdong Yueluo Hardware Industry Co., Ltd., the cone includes a large diameter end and a small diameter end, the diameter of the large diameter end is the same as the diameter of the inner hole in the middle of the nail body, and the diameter of the small diameter end is Two-thirds of the diameter of the large diameter end.
In order to solve the above technical problems, Yueluo provides a screw installation method. When using this method to install screws, the sensor must sense that the screws have been adjusted to the specified position before allowing the screws to be energized, which prevents the screws from being adjusted. Accidents of personal injury caused by operating errors during the process. The technical solution adopted by Yueluo to solve its technical problems is a screw installation method, which includes the following steps: a. Fix the screw hole structure that needs to be installed on the workbench, and fix the corresponding size screw to the screw mouth; b. Adjust the sensor on the track groove to the vertical position just above the screw hole structure; c. Adjust the screw position until the sensor on the screw senses the signal sent by the sensor; d. Turn on the screw power supply, and install the screw into the screw Inside the hole structure, the installation is complete. Compared with the prior art, Yueluo has the following beneficial effects. The screw installation method provided by Yueluo has the steps of preventing accidental hitting, which avoids personal injury accidents caused by operation errors during the screw adjustment process.
Guangdong Yueluo Hardware Industry Co., Ltd. provides a nut provided by Yueluo, which includes an internal thread. is an arc curve. Compared with the nut of the same type, the normal pressure and friction force of the nut are increased, the thread is not easy to loosen, and the bolt and nut are in surface contact, so it is not easy to cause stress concentration and local material yield, which effectively improves the tightening force of the bolt and nut. Stability, increase fastening reliability.
1) Scope This standard specifies the lock nut (referred to as nut), the size of the locking device, technical requirements, acceptance rules and measurement methods. This standard applies to the design, production, inspection and user acceptance of nuts and locking devices for tapered bushings. 2) Terminology The terms used in this standard conform to the provisions of GB/T 6930. This standard specifies the marking system, index, test method and marking of the mechanical and working performance of the effective torque section steel hexagonal lock nut. This standard is applicable to coarse thread 6H class nuts made of carbon steel or alloy steel, the width across the sides conforming to the provisions of GB 3104, the nominal height is ≥ 0.8D, and the guaranteed load and effective torque need to be specified, and the thread diameter is 3 ~ 39mm. Except for the effective torque part, the thread size and tolerance are specified in GB 193, GB 196 and GB 197. The working temperature range of the nut should be in accordance with: All-metal nut without electroplating treatment: -50℃～+300℃. All-metal nuts with electroplating treatment: -50℃～+230℃; nuts embedded with non-metallic elements: -50℃～+120℃. This standard does not apply to nuts with special performance requirements (such as weldability and corrosion resistance). For stainless steel and non-ferrous metals with fine pitch lock nuts or thin nuts made of carbon steel or alloy steel, the performance indicators and test methods of effective torque specified in this standard may be adopted by mutual agreement.
The equipment is tightened and fixed by screws during assembly. During high-speed operation, the equipment will generate high-frequency micro-vibration. This micro-vibration can easily lead to loosening of screws, resulting in weak connection of components and easy to cause safety accidents. Fastening is attached great importance. Many companies even directly weld the screw caps after using screws to fasten the components. However, this practice greatly hinders the subsequent maintenance and also seriously affects the maintenance and maintenance of the equipment; The emergence of tightening screws has attracted the attention and favor of enterprises; however, the self-tightening screws I use are mainly imported, and when the trade war begins, the shortage of this autonomous technology will severely limit my defense.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: round head plum blossom anti-theft screws, food grade round rubber gaskets, pin flat head bolts, square coupling gasket manufacturers and other products, we can Provide you with the right fastener solution for you.
