Service HotlineThe flange nut and the general hexagon nut are basically the same in size and thread specification, but compared with the hexagon nut, the gasket and the nut are integrated, and there are anti-skid tooth patterns on the bottom, which increases the nut and the workpiece. Compared with the combination of ordinary nut and washer, it is stronger and has greater tensile force. In some equipment with large vibration amplitude, due to the action of huge vibration force, the flange nut is prone to loosening, which often occurs. If the flange nut falls off the equipment or even damages, the staff also needs to install the flange nut repeatedly, which increases the labor intensity and brings great inconvenience to the use. Now a split type tightening nut is proposed.
Pin riveting is an important procedure in the production process. At first, people used manual work, which has low production efficiency, high production cost, and high defect rate of products produced. Later, a pin riveting machine appeared. The pin riveting machine is a For riveting and pinning of hardware products, the pin riveting machine can complete the operation of pin loading and riveting pins, and the pin riveting machine reduces the process of pin loading and riveting pins in the hardware production process. However, its structural design is unreasonable and the operation is very inconvenient
As shown in Figures 1 and 2, Yueluo is an automatic locking screw. From bottom to top, there are screw head 1 with external thread, screw rod and nut 3. The screw rod is a hollow screw rod 2, and the hollow screw There are long holes 7 on both sides of the rod 2, the width of the long hole 7 is smaller than the inner diameter of the hollow screw rod 2, and a spring 4 is arranged in the inner cavity of the hollow screw rod 2, and the spring 4 is not smaller than the hollow screw rod 2 in the free extension state. The upper end of the spring 4 is provided with a plug 5, the distance between the two wings 6 of the plug 5 is greater than the diameter of the nut 3, and the two wings 6 of the plug 5 protrude out of the hollow screw rod 2 through the long hole 7. When using the Yueluo, you only need to compress the spring through the two wings, insert the U-shaped clip after the neutral position is exposed, and then release the two wings, the spring will automatically return and compress the U-shaped clip, which is easy to use, safe and reliable. Claim 7. A self-locking screw, from bottom to top, is a screw head, a screw rod and a nut provided with an external thread, characterized in that the screw rod is a hollow screw rod, and both sides of the hollow screw rod are respectively provided with Long hole, the width of the long hole is smaller than the inner diameter of the hollow screw rod, the inner cavity of the hollow screw rod is provided with a spring, the upper end of the spring is provided with a plug, and the two wings of the plug protrude out of the hollow screw rod through the long hole.
The existing screw generally includes a round table-shaped nail body with one large end and one small end, a threaded section is provided on the radial circumference of the nail body, a small end of the nail body is provided with an inclined tip, and the large end of the nail body is provided with a nail cover. , generally used on materials that are softer than the screw, and drill into the object to be nailed through its own rotation. When drilling, the thread plays the role of rotary cutting, so that the screw is drilled forward, but when the thread cuts the object to be nailed When it is shaken for a long time, the tightening force of the screw in the axial direction is not enough, it is easy to loosen, and there is a potential safety hazard.
Due to the high demand for electronic products and the reduction of assembly line workers, in order to cope with the problem of labor shortage, manufacturing factories need to use automatic screw locking equipment to replace manual labor. In the existing automatic locking and paying equipment, most of them use a screw arranging machine to arrange the screws, and an electric screwdriver (electric batch) takes the screws back and forth, or the special equipment blows the screws into the electric batch to send the screws to the electric batch, and back and forth. The method of taking is too time-consuming, and the method of blowing air is not suitable for screws with small aspect ratios.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: pass-through gauges, 4304 stainless steel screws, carbon steel cylindrical pins, hexagonal head expansion bolts and other products, we can provide you with suitable fastening for you piece solution.
