Service HotlineScrews are very small screws used for indispensable industrial necessities in daily life, such as cameras, glasses, clocks, electronics, etc.; general screws for televisions, electrical products, musical instruments, furniture, etc.; large screws are used for engineering, construction, and bridges; Transportation equipment, airplanes, trams, automobiles, etc. use large and small screws together. At present, in the machine assembly production line, when the flat washers, spring washers and screws are matched during the screw assembly process, the flat washers, spring washers and screws are easy to fall into the product due to their small size, resulting in low screw matching efficiency. If there are flat washers, spring washers, screws, etc. that fall into the product and are not found in time and left inside the product, it may cause damage to the machine structure, and even cause casualties in serious cases.
Nuts are used as fasteners, and most of them need to be used in conjunction with gaskets in the process of use to adjust the deficiencies of the material itself and strengthen the degree of tightening, while metal materials are used as raw materials for gaskets. The cost is also relatively high, and in the process of use, the end face of the metal gasket and the nut will also be affected by the process, resulting in the defect that the fastening effect is not firm and easy to loosen.
square nut described by Guangdong Yueluo Hardware Industry Co., Ltd. includes a nut body 1, the nut body 1 is in the shape of a cube, the side length is 7.6mm, and the height is 2.4mm. The upper and lower ends of the nut body 1 are respectively set. There are circular protrusions 2 and circular protrusions 3 with a height of 0.25mm, and the circular protrusions 2 and the circular protrusions 3 are respectively tangent to the upper and lower surfaces of the nut body 1 in a square shape. A through hole 4 is provided in the middle of the shaped protrusion 2 and the circular protrusion 3, and runs through the nut body 1. The opening of the through hole 1 is provided with a chamfer 5 of 30°, and a thread 6 is provided on the inner wall of the through hole 4. , the circular protrusion 2 is provided with a number of strip-shaped protrusions 7 along the circumference inward to the opening of the through hole 4. The number of the strip-shaped protrusions 7 can be arbitrary, and the ideal number is 26, and the through hole 4 is open. There are several strip-shaped grooves 8 at the circumference of the circular protrusion 3. The number of strip-shaped grooves 8 can be arbitrary, and the ideal number is 26. The circular protrusions 2 and the circular protrusions 3 There is a chamfer 9 of 15° extending outward to the prism of the nut body 1 . The production of square nuts described by Guangdong Yueluo Hardware Industry Co., Ltd. is basically the same as the traditional nut process. The key point is to use a punching machine to punch out circular protrusions on both ends. High, and the circular protrusion 2 is punched again to make a bar-shaped protrusion 7, and at this time, the height of the circular protrusion 2 is consistent with the plane height of the circular protrusion 3, and the circular protrusion 3 is formed by stamping. groove 8. The contact surface of the nut body 1 is increased by providing circular protrusions 2 and circular protrusions 3 on the upper and lower end surfaces of the nut body 1, and respectively providing a bar-shaped protrusion 7 and a bar-shaped groove 8 at the two circular protrusions. Therefore, the friction between the nut body 1 and the fastener is effectively increased, and a good fastening effect is achieved.
The use of the screw is mostly used in plastic molding equipment, such as plastic profile extruders, injection molding machines, etc. Screw and barrel are the core components of plastic molding equipment. It is the part of heating extrusion plasticizing. It is the core of plastic machinery. Screws are widely used in machining centers, CNC machines, CNC lathes, injection molding machines, wire cutting machines, grinding machines, milling machines, slow wire walking, fast wire walking, PCB drilling machines, engraving machines, engraving and milling machines, spark discharge machines, tooth bite machines , planer, large vertical lathe gantry milling, etc.
Round head three-combination screw The screw size in the round-head three-combination screw is GB818, and the main technical requirements of various types are: iron and stainless steel material requirements, iron low, medium, high carbon steel, stainless steel combination The materials of the screws are stainless steel 201, stainless steel 304 and stainless steel 316. The thread tolerance is 6G, and the mechanical properties of the iron combination screws are 4.8 and 8.8. The 4.8-level combination screws are ordinary steel, and the maximum allowable hardness is 255HV. The 8.8-level combination screws are generally made of wire rod 10B21. , and then undergo hardening treatment, and then dehydrogenation after hardening treatment. Hydrogen removal is to prevent hydrogen embrittlement of the spring washer in the combination screw. Prevent the spring pad from breaking. The tolerance class of the combination screws is A. The cross groove is H-shaped. The surface treatment of the combination screw has environmental protection and non-environmental protection. Such as, environmental protection blue zinc, environmental protection color zinc, black zinc, color zinc, white nickel and so on. The technical requirement of the combination screw for the spring washer is that the washer should be able to rotate automatically without falling off.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: slotted lock nuts, finger screws and bolts, closed flat round head rivets, square T-shaped sliders and other products, we can provide you with suitable products Your fastener solution.
