Service Hotlinerivet nut is a tool for riveting nuts, which can be used for riveting the nut to a sheet and has a wide range of uses. Most of the existing rivet nuts have a double-handled structure, which is complicated in structure and high in cost; and the double-handled structure generally requires both hands to operate due to the large distance between the two handles, which is inconvenient to operate. Technical realization elements: In order to solve the above technical problems, Yueluo provides a rivet nut with simple structure, low cost and convenient operation. The technical solution adopted by Yueluo is: including a fixed body, a sliding body, a guide sleeve, a nut, a hollow screw and a handle;
There are many types of T-bolts used with pre-embedded chutes, which are used for the connection of external components of pre-embedded chutes embedded in segments, U-beams, building concrete, etc. The fixing of the chute on the forming die. When producing segments and U-shaped beams, the embedded chute is fixed on the forming mold by T-bolts. During the concrete pouring process, the tightening nut is easily covered by concrete. In this way, the concrete on the fastening nut should be removed, but it is difficult to remove the concrete, which will cause inconvenience to the disassembly of the forming mold after the production of the segment and the U-shaped beam.
flat washer, an annular groove is formed on the outer side of the upper surface of the flat washer, and a sealing ring is embedded in the annular groove, at least five circularly equidistantly arranged cylinders are fixed on the upper surface of the flat washer, and the The upper surface of the flat washer is provided with a circular hole that communicates with its bottom, a collar is arranged in the circular hole, an upper circular ring is fixed above the collar, a lower circular ring is fixed below the collar, and the upper circular The diameter of the ring is the same as the diameter of the lower ring, the diameter of the collar is smaller than the diameter of the upper ring, the diameter of the collar is consistent with the diameter of the circular hole, and there are at least three equally spaced holes in the middle of the outer wall of the flat washer. A circular groove, the outer wall of the flat washer is fixed with at least three reinforcing blocks staggered with the circular groove, and the reinforcing blocks and the flat washer are welded into one piece.
Nuts are usually used in conjunction with bolts or screws to fasten other components and are a common and widely used component. In order to make the nut not easy to loosen and fall off when it is subjected to strong vibration and irregular strong toggling, the combined nut has appeared on the market.
High-strength fastener materials mainly include ML35, 35K, ML40Cr, ML35CrMo steel, etc., of which 75ML35CrMo steel is imported. The main problems of the material are box segregation, decarburization, cracks and so on. The material needs to be spheroidized and annealed before cold forming, and the annealing is carried out in an oil furnace. There is no protective atmosphere in the furnace, and there is a decarburization phenomenon. 1.2 The high-strength fasteners, mainly grade 12.9, are quenched and tempered on the chain casting furnace production line. The temperature and atmosphere in the furnace are controlled by computer, and Rx gas is used as a protective atmosphere. Heating and anti-oxidation and decarburization can be effectively controlled, and the quality of the fasteners is intact during the heating process. The high-strength fasteners mainly of grade 8.8 are quenched and tempered on the vibrating hearth furnace. Affected by the structure of the vibrating hearth furnace, the sealing performance of the furnace is poor, the Rx atmosphere is not easy to control, the temperature difference of the furnace is large, and the parts are heated in the furnace. The collision and the length of time are inconsistent, and the quality of the fasteners during the heating process is poor, and there are phenomena such as decarburization, bumps, and uneven heating.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: injection-molded knurled copper nuts, self-locking anti-skid and anti-falling nuts, 4.8 grade spring washers, round decorative screws and nuts and other products, we can provide products such as You have the right fastener solution for you.
