Service HotlineReferring to Figure 1, one end of the existing insert nut 1' is embedded in the injection molded part 2', and the other end is exposed to the injection molded part 2'. The insert nut 1' has opposite lower and upper end surfaces in the axial direction. The end face of one end of the insert injection molded part 2' is the lower end face. In order to reduce the resistance during hot pressing, the connection between the inner wall surface and the lower end surface of the insert nut 1 ′ is provided with an inclined surface. However, when the embedded nut 1' of this structure is hot-pressed, the hot melted glue will generate a shunt that rises along the slope, and then a convex peak is formed in the screw hole of the embedded nut 1', and the convex peak occupies the screw. The space in the hole prevents the screw 5' from being completely screwed in; at the same time, due to the shunting of the hot solder, the knurling of the inner nut 1' near the upper end face cannot be filled with the solder, which makes the inner nut 1' and the inner nut 1' and The injection part 2' is not firmly embedded. Therefore, the locking strength of the existing insert nut 1 ′ and the screw 5 ′ after being hot-pressed is relatively low.
The flat washer is mainly used to reduce the pressure. When some parts are tightened with a large axial force, it is easy to press the washer into a dish shape. At this time, it can be solved by changing the material and increasing the hardness.
Iron two combination screws can be sucked up with magnets, but stainless steel two combination screws are difficult to be sucked up. Environmentally friendly three-combination screws and non-environmentally friendly ones are invisible to the naked eye and require mechanical testing. It cannot be judged with the naked eye and out of thin air. The specifications of the two combination screws need to be determined by the national standard. The salt spray of the two combination screws needs to be measured with a salt spray machine for how many hours.
The existing welding stud only has one welding spot on the top surface of the screw head, and the welding stud is relatively long and thick. When welding, the current will be relatively large, so that all the welding spots can be melted to complete the welding process. Because there is only one welding spot, and the welding stud is relatively long and thick, the increase of the current during welding will deform the melting point of the metal plate, which will lead to the penetration of the metal plate, which will lead to the concave and convex welding scars on the back of the welded plate, which will affect the appearance. Only one welding spot is located to be welded with the metal plate. During welding, the uneven parallelism of one spot leads to insufficient stability and a certain slope. It is easy for workers to have insufficient stability and parallelism when operating, resulting in wasted time and high scrap rate. increase.
An elastic cylindrical pin assembling device, the assembling device includes an adapter handle, a punching needle, an elastic piece, a fixed sleeve and a telescopic sleeve, the adapter handle and the fixed sleeve are fixedly connected, and the punching needle is inserted into the adapter handle and fixed Inside the sleeve and its upper end is pressed against the adapter handle, the lower end of the punch needle is also inserted into the fixed sleeve and moves relative to the fixed sleeve in the up and down direction when the adapter handle pushes it to move up and down, the fixed sleeve A reset spring is also set between the punch and the punch, the lower end of the fixing sleeve has an insertion hole for the elastic cylinder pin, that is, a working cavity, and the lower end of the punch needle is also provided with a push fit for the upper end of the elastic cylinder pin. the positioning boss. When the elastic cylindrical pin assembling device is used, after assembling an elastic cylindrical pin, the elastic cylindrical pin needs to be re-installed into the fixed sleeve, which cannot realize continuous assembly and has low assembly efficiency.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: external hexagonal reverse screw bolts, DIN7991 screws, color zinc cross screws, wire rope tension screws and other products, we can provide you with suitable tightening screws for you. Firmware Solutions.
