Service Hotlinesquare nut described by Guangdong Yueluo Hardware Industry Co., Ltd. includes a nut body 1, the nut body 1 is in the shape of a cube, the side length is 7.6mm, and the height is 2.4mm. The upper and lower ends of the nut body 1 are respectively set. There are circular protrusions 2 and circular protrusions 3 with a height of 0.25mm, and the circular protrusions 2 and the circular protrusions 3 are respectively tangent to the upper and lower surfaces of the nut body 1 in a square shape. A through hole 4 is provided in the middle of the shaped protrusion 2 and the circular protrusion 3, and runs through the nut body 1. The opening of the through hole 1 is provided with a chamfer 5 of 30°, and a thread 6 is provided on the inner wall of the through hole 4. , the circular protrusion 2 is provided with a number of strip-shaped protrusions 7 along the circumference inward to the opening of the through hole 4. The number of the strip-shaped protrusions 7 can be arbitrary, and the ideal number is 26, and the through hole 4 is open. There are several strip-shaped grooves 8 at the circumference of the circular protrusion 3. The number of strip-shaped grooves 8 can be arbitrary, and the ideal number is 26. The circular protrusions 2 and the circular protrusions 3 There is a chamfer 9 of 15° extending outward to the prism of the nut body 1 . The production of square nuts described by Guangdong Yueluo Hardware Industry Co., Ltd. is basically the same as the traditional nut process. The key point is to use a punching machine to punch out circular protrusions on both ends. High, and the circular protrusion 2 is punched again to make a bar-shaped protrusion 7, and at this time, the height of the circular protrusion 2 is consistent with the plane height of the circular protrusion 3, and the circular protrusion 3 is formed by stamping. groove 8. The contact surface of the nut body 1 is increased by providing circular protrusions 2 and circular protrusions 3 on the upper and lower end surfaces of the nut body 1, and respectively providing a bar-shaped protrusion 7 and a bar-shaped groove 8 at the two circular protrusions. Therefore, the friction between the nut body 1 and the fastener is effectively increased, and a good fastening effect is achieved.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to overcome the above shortcomings and provide a limit screw. The technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. is realized in the following way. Its structure is composed of screws, hexagonal copper posts and limit necks. The left end of the limit neck is open, the hexagonal copper column is communicated with the inside of the limit neck, and the inside is provided with screw threads. The design length of the screw thread in the hexagonal copper column is 1/3-2/3 of its own length. The advantages of Guangdong Yueluo Hardware Industry Co., Ltd. are (10), which can effectively prevent the problem of poor memory contact caused by the increase of the deformation of the motherboard due to the warping and deformation of the motherboard during installation and fixation, and can effectively control the deformation. effect.
An anti-loosening nut structure includes a flat nut and an oblique nut. One end surface of the oblique nut is an oblique surface, and an angle is formed between the oblique surface and the vertical line of the screw hole axis of the oblique nut. Nuts are installed on the bolts one after another, and the mating contact surfaces of the two nuts include the inclined surface, which are tightened in sequence.
The diameter, length and quantity of the stud bolts shall meet the requirements, and the type and material of the stud bolts shall be determined by the grade. There are two types of commonly used stud bolts (also known as full-threaded studs). The thread is divided into two types: coarse thread and fine thread. The coarse thread ordinary thread is expressed by M and the nominal diameter, and the fine thread ordinary thread is expressed by M and the nominal diameter × pitch. The fastener standard stipulates that M36 bolts use coarse thread, M36 and above diameters can use fine thread, and the pitch is 3. bm=1d studs are generally used for the connection between two steel connected parts; bm=1.25d and bm=1.5d studs are generally used between cast iron connected parts and steel connected parts The connection between the two; bm=2d double-ended stud is generally used for the connection between the aluminum alloy to be connected and the steel to be connected. The former connector has internal threaded holes, and the latter connector has through holes. The threads at both ends of the equal-length studs need to be matched with nuts and washers, and are used for two connected parts with through holes. One end of the welding stud is welded on the surface of the connected piece, and the other end (threaded end) passes through the connected piece with a through hole, and then the washer is put on, and the nut is screwed on, so that the two connected pieces are connected as a whole.
With the advancement of technology in various industries, the current structural design of screws has evolved from just simple locking to focusing on work efficiency during the locking process and not destroying the integrity of the objects to be locked. The new cases such as No. 556784 screw improvement and No. 289405 screw that integrates locking, stability, labor-saving, fast and multi-function which were previously designed and approved and published in the Central Taiwan Bulletin are the main representatives of screws. It is clear that It is learned that the two cases not only fully improve the shortcomings of the traditional simple locking screws, but also achieve the purpose of substantial improvement of the screws designed in each case in actual use.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: anti-loose spring steel washers, red red steel paper washers, GB854 washers, self-locking and back-stop colored screw caps and other products, we can provide you with The right fastener solution for you.
