Service HotlineIn order to achieve this technical purpose, the plan of Guangdong Yueluo Hardware Industry Co., Ltd. is: a new type of open rivet, including a rivet body and a mandrel, the rivet body and one end of the mandrel are fixedly connected, and the lower end of the rivet body is provided with There is a round table, the top of the mandrel is provided with a nail head pit, the mandrel is provided with a stop groove, the lower side of the stop groove is provided with a mandrel breakpoint, and the mandrel is set on the mandrel. There is a stop ring, the stop ring is located on the lower side of the round table, and the lower side of the stop ring is provided with an assembly warp.
① Nominal thread outer diameter (thread specification): divided into metric system and inch system. Metric thread → common specifications are 2; 2.3; 2.5; 2.6; 2.9; 3; 3.1; 3.5; 4; 4.2; 4.5; The unit is mm (millimeters). Inch thread→ Common specifications are 2#;4#;6#;8#;10#;12#;1/4;7/32;5/16;3/8;1/2 ;9/16;3/ 4. The unit is in (inches). ② Number of teeth/pitch: Definition of number of teeth → the number of teeth lines in one inch (25.4mm) length. Pitch Definition → Distance value between two adjacent threads. Conversion of number of teeth and pitch of teeth → pitch of teeth = 1 inch/number of teeth ③Nominal length: divided into metric system and inch system. Metric Nominal Length → Common values are 5, 6, 6.5, 7, 8, 9, 9.5, 10, 11, 12, 13, 14, 15, 16, 18, 19, 20, 21, 25, 28, 30, 31 , 32, 35, 40, 42, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100, 110, 120. The unit is mm (millimeters). Imperial Nominal Length → Common values are 1/4, 5/16, 3/8, 7/16, 1/2, 5/8, 3/4, 1, 2, 3. Units: in (inches). ④Head type: use letters to indicate the type of head type, please refer to the previous classification of commonly used screw head types. ⑤Tooth type/tail type: Use letters to indicate the type of tooth type/tail type, please refer to the previous Commonly used screw thread/tail type classification. ⑥Groove type: Please refer to the previous section Category of common screw groove types of our company. Cross-slotted or non-slotted (such as punched hexagon head screws) do not need to be marked here, and other groove types need to be described in words. ⑦Special labeling: In general, no labeling is required. When expressing its characteristics, it is described in words at this position. For example: the specification name of the screw is described as 4-0.7x70PM±tooth length 35, which means 4 is the nominal diameter of the screw thread, 0.7 is the pitch, 70 is the nominal length of the screw, and P means its The head type is a pan head, M means its tooth type/tail type is a wire thread type, ± means its groove type is ± groove and can also be expressed by plus or minus groove. Tooth length 35 is special Mark, specify the thread length value of this screw.
kind of nut provided by Yueluo, the nut is in the shape of a casing and is provided with a threaded section. The two ends of the threaded section are respectively provided with two convex blocks, and the convex block at the front end of the screw-in direction reaches the hole core. The distance is greater than the nominal size of the thread segment, and the distance from the rear end projection in the screwing direction to the hole core is smaller than the nominal size of the thread segment.
flat washer is a part that is placed between the connected part and the bolt to protect the surface of the connected part from being scratched by the nut and to disperse the pressure of the nut on the connected part. At present, a flat washer in the prior art generally includes a washer body; the washer body has a bolt hole in the middle for a bolt to pass through. Although the flat washer of the above structure has a simple structure, it still has a disadvantage. When the flat washer is cushioned between the connected part and the bolt, the bolt head is usually exposed outside the connection part, so the bolt head is easy to It is damaged under the impact of external force, thus affecting its fixing effect.
Screw refers to a screw, which is a tool that uses the physical and mathematical principles of the inclined plane, circular rotation and friction of an object to gradually fasten objects and parts. A screw is a common term for fasteners. Fasteners are widely used in machinery, electrical appliances and buildings. They are generally made of metal or plastic, cylindrical in shape, and grooves engraved on the surface are called threads.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: large flat head screws and screws, GB6173 small tooth flat nuts, set nuts, thick square washers and other products, we can provide you with products suitable for you fastener solutions.
