Service HotlineMine trucks are required for underground construction and coal transportation. With the vigorous development of energy, the output of coal has increased significantly, and the demand for mine trucks has increased. The axle card is an important part of the mine car. Its shape is irregular, and the blank is a casting. It needs to be finished on the semicircular surface whose upper center is matched with the mine car axle. At present, the mine truck axle card is generally processed by a milling machine, which has the problem of low efficiency.
For the detection of the shear force of the elastic cylindrical pin, the method and the tooling are marked, but the tooling is only a means to be used on the test bench, and the process of embedding the cylindrical pin into the tooling is a more difficult process. Generally, it is used to place the tooling on a plane, a vise, a simple V-shaped, and a simple U-shaped fixture. Originally, the elastic cylindrical pin was detected by hand or pliers to hold the cylindrical pin and align the pin with the outer cylinder of the tooling. Use a hammer to smash the shear holes, and adjust the concentricity of the inner and outer cylinders of the shear holes of the tooling from time to time. The limitations, dangers and difficulties of this assembly method are relatively large, often testing a set of cylindrical pins, which takes a lot of time and is difficult for lesbians to complete.
However, although the above-mentioned screw belt (2) can achieve the expected effect, it is also found in its actual implementation. Although this structure has multiple grooves on both sides of the main body for the driving and turning of the locking screw tool, However, the groove is only used for driving the screw belt drive, and since the screw will swing on the screw belt, it is impossible to stably align the screw on the screw belt with the point where the screw is to be set. , which leads to great inconvenience in operation and use, and also affects the efficiency of screw and screw installation, so that there is still room for improvement in the overall structural composition.
Ordinary T-bolts, the bolt head is rectangular, the screw part and the bolt head are T-shaped, and the width of the head is smaller than the width of the opening part of the T-slot, so that the head of the T-bolt can extend from the length of the T-slot. Insert the T-slot into the T-slot at any position in the direction. When the workpiece needs to be fixed, turn the T-bolt 90 degrees so that the length of the head is perpendicular to the T-slot, hook the inside of the opening of the T-slot, and screw it by tightening The nut on the T-bolt threaded rod holds the workpiece in place. The T-bolt of this structure can easily connect the bolt and the base piece quickly, and is widely used, but there are also some shortcomings, due to the contact area between the head of the T-bolt and the inner side of the opening of the T-slot. If it is too small, the frictional resistance is correspondingly small. On the one hand, the bolts are easy to follow the rotation during the process of tightening the nut. Unreliable.
1. Ordinary outer hexagon - widely used, characterized by relatively large tightening force, the disadvantage is that there must be enough operating space during installation, and adjustable wrench, open-end wrench or glasses wrench can be used during installation, all of the above wrenches require a large amount of space. operating space. 2. Cylindrical head hexagon socket - is the most widely used of all screws, because it has a relatively large tightening force, and can be operated with a hexagon wrench. It is very convenient to install and is used in almost all kinds of structures. The appearance is more beautiful and neat. The disadvantage is that the tightening force is slightly lower than the outer hexagon, and the inner hexagon is easily damaged due to repeated use and cannot be disassembled. 3. Pan head inner hexagon - rarely used mechanically, the mechanical properties are the same as above, mostly used in furniture, the main function is to increase the contact surface with wooden materials and increase the ornamental appearance. 4. Headless inner hexagon - must be used in certain structures, such as the top wire structure that requires a large top-tight force, or where the cylindrical head needs to be hidden. 5. Countersunk head hexagon - mostly used in power machinery, the main function is the same as the inner hexagon. 6. Nylon lock nut - a nylon rubber ring is embedded in the hexagonal surface to prevent the thread from loosening, and it is used on strong power machinery. 7. Flange nuts - mainly play the role of increasing the contact surface with the workpiece, mostly used in pipes, fasteners, some stamping parts and casting parts. 8. Ordinary hex nut - the most widely used and one of the most common fasteners.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: 8.75 outer diameter hexagon socket bottom hole, hexagon nut with washer, hollow pin positioning pin, square hole cage nut and other products, we can provide You have the right fastener solution for you.
