Service HotlineTwo combination screws are mostly used for the connection between thin metal plates, and play a connecting role. When connecting, first make a threaded bottom hole for the connected piece, and then screw the combination screw into the threaded bottom hole of the connected piece. Since the threaded surface of the combination screw has high hardness, the inner thread can be tapped in the threaded bottom hole of the connected piece to form a connection.
The technical solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. to solve its technical problems is: a waterproof rivet, including an integrally formed waterproof cap and a rivet rod for waterproofing, and the waterproof cap includes a lower part that is fixedly connected with the rivet rod. An end face, the lower end face includes a fixing portion arranged in order from the center position of the lower end face to the outside, a buffer portion arranged circumferentially with the fixing portion as the center, and a waterproof portion arranged circumferentially with the fixing portion as the center, the fixing portion and the rivet The rods are fixedly connected, and the section of the waterproof part is a figure-eight shape.
The national standard name of the cross recessed small pan head three-combination screw is the cross recessed small pan head screw, the spring washer and the flat washer assembly. The national label is GB/T9074.8-1988. This 1988 refers to the year, that is, this standard is the standard issued by the country in 1988. The specifications of the cross recessed small pan head three-combination screw, our company's minimum is M2.5, the shortest is 5mm, the largest is M10, and the longest is 90mm. Of course, as customers have higher and higher requirements for small pan head combination screws, or require smaller and longer combination screws. If the quantity is large, or with the development of our company. Buy some advanced combination screw machines. Come and go to meet the higher requirements of our customers.
At present, most of the cylindrical pin press-fitting is to put the product into the positioning position of the lower die first, and then take a cylindrical pin and put it into a cylindrical pin positioning hole that is concentric and perpendicular to the hole in which the product is pressed, or put it on the product. , the pin needs to have a positioning guide; or it is fixed on the top of the indenter so that it will not fall, and then the press is completed. In fact, it is difficult to press the small cylindrical pins. To ensure the good quality of the product, it is required to locate accurately, to ensure that the cylindrical pins are concentric and vertical, and to put the cylindrical pins one by one. It is very easy for workers to produce. Fatigue and low efficiency, product quality control is affected by many human factors, resulting in unstable product quality and certain safety hazards in work. On the other hand, in some production lines, the cost of the press-in cylindrical pins is relatively expensive, such as finger cylinders and moving mechanisms, which will put a lot of cost pressure on the equipment investment of small and micro enterprises.
The hinge is a hinge, which is often composed of two folds. It is a part that connects the two parts of the object and can make it move. The hinge supporting screws are installed on the corresponding objects. For different use environments, the requirements for the supporting screws are also different. different. Most of the existing screws are set to a single-threaded structure. When used to cut into a wooden door, the cutting speed is slow, and the cutting effect is not ideal, which is not conducive to cutting into a hard wooden door, etc., and the commonly used screws are often made of iron materials. It is easy to rust after contact with water vapor, reducing the service life; in addition, when the screw is driven into the wooden door, the chips generated cannot be discharged in time, and stay inside the wooden door and surround the screw, forming expansion stress, thereby squeezing the wooden substrate, which is not conducive to the screw. The connection with the wooden door is stable, which easily affects the normal installation of the hinge, and the use effect is poor. To sum up, in order to solve the shortcomings of the existing screw structure for hinges, Guangdong Yueluo Hardware Industry Co., Ltd. designed a hinge screw with simple structure, convenient use, fast construction and good effect.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: self-locking non-slip nuts, hand-tightening nuts, isolation column copper nuts, welding nuts and other products, we can provide you with suitable fastener solutions for you Program.
