Service HotlineIn the existing joint replacement, self-tapping screws are mostly used, and their triangular thread structure has a certain self-locking ability. After a long period of service, it is prone to loosening. The surrounding bone may not be tight enough after implantation, resulting in a sharp decline in its self-locking ability, and there may be a risk of regression, causing certain damage to the human body.
The process of removing iron oxide plate from cold heading steel wire rod is stripping and dephosphorization. There are two methods: mechanical dephosphorization and chemical pickling. Replacing the chemical pickling process of wire rod with mechanical phosphorus removal not only improves productivity, but also reduces environmental pollution. This phosphorus removal process includes bending method (the round wheel with triangular grooves is commonly used to repeatedly bend the wire rod), spray nine method, etc. The phosphorus removal effect is good, but the residual iron and phosphorus cannot be removed (the removal rate of iron oxide scale is 97%) ), especially when the iron oxide scale is very sticky, therefore, mechanical phosphorus removal is affected by iron scale thickness, structure and stress state. Carbon steel wire rods used for low strength fasteners (less than or equal to 6.8) High-strength bolts (greater than or equal to grade 8.8) use wire rods to remove all iron oxide scales after mechanical dephosphorization, and then go through a chemical pickling process for compound dephosphorization. For low carbon steel wire rods, the iron sheets left by mechanical dephosphorization are likely to cause uneven wear of grain draft. When the grain draft hole adheres to the iron sheet when the wire rod rubs against the external temperature, the surface of the wire rod produces longitudinal grain marks. More than 95% are caused by scratches on the surface of the steel wire during the drawing process. Therefore, the mechanical phosphorus removal method is not suitable for high-speed drawing.
When fixing the centrifugal fan, since the gaskets, washers and nuts are separate parts, many parts are used in the whole process, and it is easy to miss the installation of parts; The volume of the parts is relatively small, and it is not easy to remove them when they are transferred into the air conditioner through the gap of the centrifugal fan blades, resulting in foreign bodies in the machine.
Embodiments of Guangdong Yueluo Hardware Industry Co., Ltd. are described in detail below, examples of which are shown in the accompanying drawings, wherein the same or similar reference numerals represent the same or similar elements or elements with the same or similar functions throughout. The embodiments described below by referring to the accompanying drawings are exemplary, and are intended to be used to explain Guangdong Yueluo Hardware Industry Co., Ltd., and should not be construed as a limitation to Guangdong Yueluo Hardware Industry Co., Ltd.
For common screw belts, please refer to the Central Taiwan Announcement No. 327442 Screw Belts (2) on February 21, 1998. It includes a main body, and there are multiple grooves on the side of the main body, which are used for locking screw tools to drive the belt. A toggler; and a plurality of nail grooves are arranged on the nail belt so that the screw planting is arranged in an arrangement, and the nail grooves are all provided with through holes, and the through holes extend downward with a ring to form a support portion for the screws; and the It is surrounded and provided with a plurality of cutting grooves, which is beneficial for the screw to be rotated through the nail groove; and it is characterized in that the nail groove is located on the inner wall surface of the surrounding and is provided with a plurality of lobes, and these lobes are implanted in the screw. In the nail groove, the leaflet supports the screw, so that the screws with different outer diameters are fully supported and positioned by the leaflet; and/or the upper part of the leaflet is inclined or curved, so that a depression is formed above the ring to support the screw The arc surface or tapered surface of the neck can make the screw more stable to be supported.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hydraulic oil-filled bolts for oil return pipe hinge joints, Daquan 304 stainless steel nuts, titanium nuts, gb5782 half-tooth external hexagon screws and other products, we can provide you with The right fastener solution for you.
