Service HotlineThere are two typical pin shearing fixture tooling, among which the traditional fixture shown in Fig. 1 is more complicated and consists of fixture, spacer, washer and shearing block guide post, hardened bushing, shearing block and so on. The cylindrical pin is installed in the hardened bushing, and the axial load is applied through the shear block to complete the shear test. The fixture is complicated in manufacture and has many consumables, because the size of the hardened bushing is similar to that of the cylindrical pin. , and to keep the notch of the cylindrical pin upward, it is difficult to install before the test, and the broken cylindrical pin after the test remains in the hardened bushing and is difficult to remove.
During the tightening process of the screw, do not use excessive force, otherwise the product will be damaged. The traditional bolt locking adopts manual operation, which is inefficient and insufficient force. In the existing screw locking device, before locking the screw, the locking force of the screw is tested, but the test equipment is set separately, resulting in a complicated structure. In addition, in the existing screw locking device, when the screw is locked, the position of the screw hole is not corrected, so that the screw often causes damage to the product during the tightening process.
In order to overcome the above problems, Guangdong Yueluo Hardware Industry Co., Ltd. provides a screw that can be quickly installed and removed. Using the principle of lever, press the handle downward, and the screw can form a backward force through the connecting piece. Press the screw and nut tightly; lift the handle, the screw forms a forward force, and the screw can be removed. Thus, the time and manpower for screwing during installation and disassembly are reduced. The solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. to solve its technical problems is that the entire screw includes a screw rod, a nut, a connecting piece, a circlip, a positioning pin, a small shaft, a fixed piece, a base, and a handle; the screw is connected by the small shaft at the upper end. At the upper end of the connecting piece, the handle is connected to the lower end of the connecting piece, and the front end of the handle is connected to the base fixing piece through a positioning pin. There are gaps at both ends of the small shaft, and the small shaft is installed through the circlip. The front end of the handle can only be rotated on the positioning pin. Due to the lever principle, when the handle is pressed down, it will drive the screw at the front end of the connecting piece, so that the screw generates a backward force and tightens the screw and the nut. On the contrary, when the handle is pulled up, the screw generates a forward force, so that the screw can be easily removed. The beneficial effect of Guangdong Yueluo Hardware Industry Co., Ltd. is that the quick-opening screw saves the time and labor of repeatedly twisting the nut during installation and disassembly. The installation and removal process is simple.
In order to solve the above-mentioned technical problems, the technical solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. is: shear rivets, including a mandrel and a deformation sleeve ring sleeved on the mandrel, one end of the deformation sleeve ring is a boss structure, and the It includes an adhesive collar sleeved on the deformation collar, the adhesive collar is a hollow annular sleeve and is filled with adhesive material; one end of the mandrel is a hemispherical head, and the spherical surface of the hemispherical head is outward, The connection between the hemispherical head and the mandrel is a conical connecting section, and the diameter of the conical connecting section gradually decreases from the hemispherical head inward; the mandrel is provided with a stress concentration groove, and the position of the stress concentration groove is close to the deformation The boss structure of the collar.
The middle pins on upright and horizontal pianos are also called balance pins. The middle pins are installed on the middle sleepers of the keyboard frame and play the role of fixing the keys. Generally, there are 88 keys in the piano. The pins are matched with the pin holes, and the keys are installed on each middle pin one by one through the pin holes. Due to the large number of middle pins and keys, in the production and installation process, in order to ensure the flatness of the 88 keys after installation, it is necessary to debug the middle pins and keys one by one, or add paper circles to the middle fixed part on the middle pins. The flatness of the 88 keys is kept the same. This debugging method is extremely cumbersome and increases the workload of debugging. Moreover, when adding paper circles, the keys need to be disassembled frequently. Due to the limitation of the installation space of the keys, it is troublesome to disassemble the keys, and it is easy to install and disassemble the keys many times. Damage to the pin holes on the keys, degrading the quality of the piano.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: 316 flat washers, pin positioning pins, carbon steel small square head bolts, external hexagon hollow screws and other products, we can provide you with suitable products for you fastener solutions.
