Service HotlineFig. 1, Fig. 2, and Fig. 3 show that the rivet nut is cut into the required blank from a chemically treated low carbon steel disc, and the blank is placed in the die, and the upper and lower punches are used for shaping to obtain a shaped blank. , and then put the shaped blank in the die, use the punch punch to cold-head out the required brim blank (1) and the deformed skirt (2), and then use the punch punch in the die to continue Cold heading out the brim blank (1) and the deformed skirt (2). Then put the semi-finished material into the concave die and use the punch of the punch to continue to squeeze the threaded hole (3) of the nut tapping skirt, and then put the semi-finished blank into the concave die and use the upper punch and the lower sleeve to drop it. material. There are fish teeth (6) below the brim; the outer side of the lower end of the threaded hole is provided with a chamfer (5); the cross-section of the thread of the inner wall of the threaded hole is an isosceles trapezoid, and the upper bottom of the trapezoid is a concave arc (4), In this way, the riveted object is firmly connected to the rivet nut.
In order to achieve this technical purpose, the plan of Guangdong Yueluo Hardware Industry Co., Ltd. is: a new type of open rivet, including a rivet body and a mandrel, the rivet body and one end of the mandrel are fixedly connected, and the lower end of the rivet body is provided with There is a round table, the top of the mandrel is provided with a nail head pit, the mandrel is provided with a stop groove, the lower side of the stop groove is provided with a mandrel breakpoint, and the mandrel is set on the mandrel. There is a stop ring, the stop ring is located on the lower side of the round table, and the lower side of the stop ring is provided with an assembly warp.
The earless retaining ring for the hole is mostly installed in the annular groove on the inner wall of the pipe fitting. The outer diameter of this kind of retaining ring is slightly larger than the diameter of the assembly round hole. When assembling, the earless retaining ring needs to be pressed into the pipe fitting. Since the inner wall of the pipe fitting is relatively smooth, the earless retaining ring is easily skewed in the pipe fitting. It needs to be adjusted several times before entering the annular groove, and the assembly efficiency is low.
High-strength self-locking nut for boats and bridges, it can convert the friction force into the expansion force between the bolt and the slot nut to achieve excellent self-locking effect. There are two slots on the upper part of the ESL nut. When the nut is tightened on the bolt, the thread of the bolt will be screwed into the slot of the cross section of the nut, and the thread will be gradually locked by the side wall of the nut to achieve the function of self-locking. The exquisite production process can keep the torque type of the locking element consistent, and the products are generally used in railway casting, rail transit, transmission system, mining equipment, highway, military, oil production machinery, automobile industry, public facilities, subway, engine, construction machinery , aerospace, drilling equipment, bridges, generators, agricultural machinery, shipbuilding industry, metallurgical equipment, trains, compressors, medical machinery, signal systems, wind power generation
Washers (spring) washers, circlips are elastic pads or card lock washers a washer that prevents bolts from loosening. The working principle of lock washers is very simple. It consists of two washers. The outside is a radial relief surface, and the inside is a helical tooth surface. When assembling, the inner helical tooth surfaces are opposite each other, and the outer radial raised surface is engaged with the contact surfaces at both ends. When the connecting piece is vibrated and the bolt tends to loosen, only the inner helical tooth surfaces of the two washers are allowed to face each other. Staggered movement, resulting in lifting tension, so as to achieve 100% locking.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hardened and quenched inner pins, inch self-locking nuts, GB898 copper posts, ultra-thin nuts and other products, we can provide you with suitable screws for you. Firmware Solutions.
