Service HotlineGuangdong Yueluo Hardware Industry Co., Ltd. discloses a through-hole mounting nut, which includes a hexagonal portion and a cylindrical portion, a threaded hole is arranged between the hexagonal portion and the cylindrical portion, and the cylindrical portion is provided with a threaded hole. Two grooves, each of the two sides of the groove has a convex side, and the upper surface of the side is provided with a convex point; the advantage is that the two sides are squeezed by the bolt, Or after the hammer is struck, it will bend to both sides, and it can be fastened to both sides of the screw hole of the sheet metal without welding.
Gaskets are mechanical seals between two objects, usually used to prevent pressure, corrosion, and natural thermal expansion and contraction of pipes between two objects and leakage. Since machining the surface is not possible, irregularities can be filled with spacers. Gaskets are usually made from sheet materials such as pad paper, rubber, silicone rubber, metal, cork, felt, neoprene, rubber, fiberglass or plastic polymers such as Teflon. Gaskets for specific applications may contain asbestos. The existing gasket is easily deformed for a long time in use, and the gasket cannot play the role of making up the difference. In addition, during the use process of the gasket, the adhesion between the gasket and the nut or the mechanical surface becomes poor, resulting in a poor sealing effect.
1. First remove the sludge on the surface of the broken head of the broken screw, use the center gun to kill the center gun of the section, and then use an electric drill to install a drill bit with a diameter of 6-8 mm to drill the hole in the center of the section, pay attention to the hole must be drilled through. After the hole is drilled through, remove the small drill bit and replace it with a drill bit with a diameter of 16 mm, and continue to expand and drill through the hole of the broken bolt. 2. Take a welding rod with a diameter of less than 3.2 mm and use a medium and small current to carry out surfacing welding from the inside to the outside in the hole of the broken bolt. Take half of the entire length of the broken bolt at the beginning of the surfacing welding. When starting the surfacing welding, the arc should not be too long. In order to avoid burning through the outer wall of the broken bolt, surfacing to the upper end face of the broken bolt, and then continue surfacing to weld a cylinder with a diameter of 14-16 mm and a height of 8-10 mm. 3. After the surfacing is completed, hammer the end face with a hammer to make the broken bolt vibrate along its axial direction. Due to the heat generated by the previous arc and the subsequent cooling plus the vibration at this time, the broken bolt and the thread of the body will be loose in between. 4. Carefully observe, when it is found that a small amount of rust leaks from the fracture after the knock, take the M18 nut and put it on the surfacing column head and weld the two together. 5. After welding, use a torx wrench to cover the nut while it is still hot, and twist it back and forth, or tap the end face of the nut with a small hand hammer while twisting back and forth, so that the broken bolt can be taken out. 6. After taking out the broken bolt, use a suitable tap to process the thread in the frame to remove rust and other debris in the hole.
In order to meet the needs of different assembled installation components, there are also hand-tightening methods for tightening the screws, but in actual use, ordinary manual screws can easily cause hand pain to the user, and the operation is extremely inconvenient; at the same time, due to tightening The contact area between the screw and the installation component is too small. If the user exerts too much force, the uneven force per unit area of the installation component will cause deformation and depression, which will affect the use. Therefore, a manual screw is proposed to solve the above problems.
In some special occasions, both objects need to be riveted and have good waterproof performance. The existing rivets have poor waterproof performance and often have problems such as water seepage.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: bolts for T-slots, red steel paper flat washers, hexagon socket bolts with small teeth, round double inner teeth and other products, we can provide you with Provide the right fastener solution for you.
