Service HotlineRelated Specifications of Automobile Welding Nuts (Square Nuts) Serial Number Standard Number Name (English) Name (Chinese) Remarks 1 MS440014 NUT,WELD Welding Square Nut M8 2 MS440013 NUT,WELD (6) Welding Square Nut M6 3 MF445605 NUT,WELD (10 ) welding square nut M10 4 MU442002 NUT,WELD welding square nut M6 parking brake handle 5 MB077464 NUT,WELD welding square nut for seat belt welding square nut 6 MB040348 BOLT WELD (10X22) welding bolt M10×22, bearing surface 7 MF198353 BOLT,WELD (6X14) Weld bolt M6×14, end face 8 MR236366 NUT (12) Nut M12 Suspended trailing arm mount 9 MS440015 NUT,WELD (10) Weld square nut M10 10 PW832525 BOLD WELD 7/16 UNF Weld bolt 7/16 For seat belt, bearing surface 11 MB528563 STUD,WELD Welding stud M6×20 12 MS440066 NUT,WELD (5/16=18UNC) Welding square nut 5/16 Child safety system 13 MS440018 NUT, WELD (6) Welding square nut M6 14 MF198375 BOLT,WELD (8X30) Welding stud M8×30 15 MF198038 BOLT, WELD (6X25) Welding bolt M6×25, bearing surface 16 MR236467 NUT (12) Welding square nut M12, for engine mount 17 MF140024 BOLT, FLANGE (8X18) Hexagon flange bolt without 3D 19 MF198036 BOLT,WELD (6X20) Weld stud M6×20 20 MF198034 BOLT,WELD (6X16) Weld bolt M6×16, bearing face 21 MS440012 NUT,WELD (5) Weld Square Nut M5 22 MB343340 BOLT,WELD (8X26) Welding Bolt M8×26, Bearing Surface 23 MB138471 STUD,WELD Welding Stud M8×46, Bearing Surface 24 MS190066 BOLT,WELD (8X16) Welding Bolt M8×16, Bearing Surface, NO 3D 25 MS240145 BOLT,WASHER ASSEMBLED (8X20) BOLT AND WASHER ASSEMBLY NO 3D 26 MB281149 NUT,WELD(6) WELD BOLTS M8, NO THREADS REQUIRED FOR BEARING 27 MF445603 NUT,WELD (6) Welded square nut M6 Reinforcing plate for rear door lock 28 MS190068 BOLT,WELD (8X20) Welded bolt M8×20, bearing surface 29 MU431507 NUT,WELD Welded square nut M8 for door hinge installation 30 MS240121 BOLT,WASHER ASSEMBLED (6X16) Bolt and washer assembly M8 for fuel filler cap 31 MS100221 BOLT,FLANGE (6X12) Flange face bolt M6 for fender mounting 32 MB344675 STUD,WELD Weld stud M6×10
There is a standard for the outer hexagon bolt standard, which is a grade standard, which is divided into grade 4.8 and grade 8.8. These two levels are used a lot in the market. Especially grade 4.8 hex head bolts. Because it is much cheaper than 8.8 hex bolts. Of course it is more widely used. But for demanding products. Because of its high requirements in various aspects such as hardness. This requires the use of 8.8 hex bolts. Grade 8.8 hex bolts are harder in terms of hardness and screw torque. It is safer to use the product. Tighter and more stable.
In order to achieve the above purpose, Yueluo provides the following technical solutions: threaded rivets include a nail rod, an expansion piece, and a nail sleeve, one end of the nail rod is provided with a mounting piece, and the side of the mounting piece away from the nail rod is movably installed with a mounting piece. There is a driving mechanism. The driving mechanism includes a mounting cylinder and a movable rod. A cross groove is formed at one end of the mounting piece close to the driving mechanism. The rod is movably installed on the inner side of the installation cylinder, and one end of the movable rod close to the cross groove is fixedly provided with a cross connecting piece that matches the cross groove, the cross connecting piece is matched with the cross groove, and the movable rod is far away from the cross groove. One end of the cross connecting piece is fixedly provided with a fixing piece, the fixing piece and the installation cylinder are screwed together by threads, the expansion piece is sleeved on the outer side of the nail rod, and the nail sleeve is movably installed on the nail rod away from the driving mechanism The outer side of one end of the nail rod is movably installed with a fixing mechanism.
The embossing wheel is used to press the mesh pattern (rolling mesh pattern), and the middle is slotted. After milling, the thread still guarantees 6H accuracy. This knurled copper nut is used in power tools, which is different from other knurled copper nuts. The diamond pattern of this knurled copper nut is located in the middle section of the product, and the diamond-shaped mesh knurling wheel rolls the diamond-shaped flower along the large outer circular step surface.
The drawing process has two purposes, one is to modify the size of the raw materials; the other is to obtain basic mechanical properties of the fasteners through deformation and strengthening. For medium carbon steel, medium carbon alloy steel also has another purpose, that is, to make the wire rod. The flaky cementite obtained after controlled cooling is cracked as much as possible during the drawing process to prepare for the subsequent spheroidization (softening) annealing to obtain granular cementite. However, some manufacturers arbitrarily reduce the drawing in order to reduce costs. The excessive reduction rate increases the work hardening tendency of the wire rod, which directly affects the cold heading performance of the wire rod. If the distribution of the reduction ratio of each pass is not appropriate, it will also cause torsional cracks in the wire rod during the drawing process. In addition, if the lubrication is not good during the drawing process, it can also cause regular transverse cracks in the cold drawn wire rod. The tangential direction of the wire rod and the wire drawing die is not concentric at the same time when the wire rod is rolled out of the die, which will cause the wear of the unilateral hole pattern of the wire drawing die to aggravate, make the inner hole out of round, and cause uneven drawing deformation in the circumferential direction of the wire. The roundness of the steel wire is out of tolerance, and the cross-sectional stress of the steel wire is not uniform during the cold heading process, which affects the cold heading pass rate. During the drawing process of the wire rod, the excessive surface reduction ratio will deteriorate the surface quality of the steel wire, while the too low surface reduction ratio is not conducive to the crushing of the flaky cementite, and it is difficult to obtain as much granular cementite as possible. , that is, the spheroidization rate of cementite is low, which is extremely unfavorable to the cold heading performance of the steel wire. For the bar and wire rod produced by the drawing method, the partial surface reduction rate is directly controlled within the range of 10%-15%.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: 1 meter aluminum alloy, natural hexagon nuts, precision machining, stainless steel hexagon thin nuts and other products, we can provide you with suitable fastener solutions for you Program.
