Service HotlineThe Chinese Patent Application No. 201320368989.2 discloses a pin, which includes a pin body and a cylindrical body part integrally provided with the pin body, a convex tip is provided on the cylindrical body part at one end of the pin body, and the convex The tip is horizontally arranged around the cylindrical body part and protrudes from the surface of the cylindrical body part. The connection between the cylindrical body part and the convex tip is provided with an inclined plane. Although this pin solves the problems of easy loosening and falling off to a certain extent, However, this kind of pin still has the problem of loosening and falling off in the case of bad working conditions and severe vibration.
Two-combination screw refers to a screw and a flat washer, or a spring washer, or a square washer, or a two-piece combination with an external tooth lock washer. Then there are all the standard types of two combination screws! The following is a brief introduction: 1. The second combination screw with spring washer refers to the combination screw with a spring washer. The spring washer is a spring washer specially used for combination screws, not the ordinary spring washer that we usually use. 2. The two-combination screw of the trim pad refers to the combination screw of the screw with a flat pad. The size of the flat pad and the thickness of the flat pad can be customized. Can be customized according to customer requirements. Flat pads are punched out by punching machines. 3. The combination screw with two external teeth refers to the screw with an external tooth combination screw. Many customers, especially electric power customers, use this external tooth two combination screw to break the paint and make the screws on the iron plate. All can be powered on. 4. Two combination screws with a square pad refer to a square pad with a square pressure line for the screw. This square pad crimping two combination screw is used on the terminal, and the function is used for crimping and wiring.
In terms of screw standard specification broadcast, there are two versions of the national standard, one is GB70-76, the 76 version, and the other is GB70-8585 version. Our company is now implementing the DIN912 standard, so it should be paid attention to in actual business operations. Difference: GB70-85 and DIN912 completely overlap, so there is no difference in the use of the new standard, mainly because there is a difference between GB70-76 and DIN912: M8 series hexagon products, GB70-76 round head diameter It is 12.5MM, which is smaller than 13.27MM of DIN912. For M10 series inner hexagon products, the round head diameter of GB70-76 is 15MM, which is smaller than 16.27 of DIN912. The inner hexagon of M12 series, the round head of GB70-76 The diameter is 18MM, which is smaller than the opposite side of DIN912, which is 18.27. In addition, the round head diameter of the inner hexagon GB70-76 of M16 and M20 series is 0.33MM smaller than that of DIN912, which are 24MM and 30MM respectively. DIN912 is 24.33MM and 30.33MM respectively. In addition, the width of the inner hexagon between the old standard and the German standard is different due to different standards. The inner side of GB70-76 is smaller, and it should be paid attention to in business operations. In addition, there are also some differences in the carriage screws that may be used at ordinary times. I will also make an explanation here. In the national standard, there are two standards for carriage screws, namely GB12 (small semicircular head square neck screw) and GB14 (large semicircular head square neck screw) Neck screws), and the German standard DIN603 is usually more commonly used in the market. Now to distinguish these three: for the round head and neck, when comparing the same specifications: GB12
High-strength self-locking nuts are a category of self-locking nuts with high strength and reliability. It is mainly based on the introduction of European technology, which is used for road construction machinery, mining machinery, vibration machinery and equipment, etc. There are very few domestic manufacturers of such products.
leak-proof combined gasket relates to a gasket and solves the problem of short service life of the existing gasket. The combined gasket comprises: an O-shaped sealing ring, which is an annular sealing ring with an outer diameter of D and an inner diameter of E. The section diameter is A; the steel outer ring is a steel flat annular outer ring, which is sleeved on the outer surface of the O-ring, the inner diameter is F, and F=D, the thickness is B, B=0.785A ;The steel inner ring is a steel flat annular inner ring, embedded in the inner surface of the O-ring, the outer diameter is G, and G=E; the thickness is C, and C=B. When the O-ring in the combined washer is pressed by the bolt for sealing, it is positioned between the steel outer ring and the steel inner ring, and is protected by both of them, so that the tightening torque of the bolt can be reduced at least Double the sealing performance without reducing the sealing performance, extending the service life of the thread and reducing the production cost.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: square head bolts, hexagonal nylon column studs, insulating flat washers, crown triple combination and other products, we can provide you with suitable fastening products piece solution.
