Service HotlineOrdinary nuts are suitable for use in fixed-load equipment. Ordinary nuts are used to fix on stationary workpieces and cooperate with flat and spring washers to ensure the reliability of the nut. However, on moving workpieces with vibration loads, the equipment may The vibration caused the nut to loosen. As a kind of nut, the slotted nut is used to connect the two mechanical equipment tightly. It is mainly used in the occasions with vibration load or alternating load. It is used in conjunction with the split pin to ensure the nut lock. The reliability of tightening is often used as a lock nut to prevent the main nut from loosening back.
Traditionally used for plastic fastening screws, most of the thread designs are self-tapping threads, but for different plastic types, the self-tapping threads also have many different classifications, such as PT profile, Plastite series, Remform profile, etc. The structural parameters and manufacturing process of these threads are inconsistent, or require different main molds and wires. Therefore, to find a plastic screw that is universally applicable to various plastic types, has a single pressing structure, low-cost and simple manufacturing process, especially its special self-tapping thread, is an important issue that needs to be solved urgently at present. question. The purpose of Yueluo Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to propose a plastic screw to solve the screw fastening problem that is generally applicable to different plastics. The purpose of Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to realize a kind of plastic screw through the following technical scheme, it is characterized in that, the thread of the screw is composed of asymmetric threads with a profile angle of 30°, and the threads are The bottom surface of the connection between them is an arc surface. Yueluo preferably, the asymmetrical thread has a forward thread angle greater than the reverse thread angle, and the sum of the two-direction thread angles is 30°. Yueluo further preferred that the tooth profile angle of the asymmetrical screw thread in the forward mounting direction is 20 degrees, and the tooth profile angle in the reverse mounting direction is 14 degrees. Yueluo Guangdong Yueluo Hardware Industry Co., Ltd.'s application of plastic screws, through the improvement of special thread structure, reduces the radial pressure and installation torque when the screw is installed, reduces the damage to the plastic hole; and increases the pull-out resistance of the screw force, it is not easy to appear loose assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
Equipment that needs to be maintained at high altitude or under complex working conditions requires screw loss prevention design. Although traditional captive screws can achieve the purpose of preventing falling off, because the diameter of the screw is smaller than the major diameter of the thread, it is difficult to match the gasket, and the gasket will be eccentric, which is easy to install. Scratch the surface of the product, affecting the corrosion resistance and appearance of the product.
(1) The surface rust, oil stains, burrs on the wall of the bolt holes, welding flashes, etc. should be cleaned up. (2) After the contact friction surface is treated, the specified anti-scratch coefficient requirements must be met. The high-strength bolts used should have matching nuts and washers, which should be used in accordance with the matching and should not be interchanged. (3) When the friction surface of the treated component is installed, it is not allowed to be stained with oil, soil and other sundries. (4) The friction surface of the module should be kept dry during installation and should not be operated in the rain. (5) Strictly check and correct the deformation of the connected steel plates before installation. (6) It is forbidden to hammer into the bolt during installation to prevent damage to the bolt thread. (7) The electric wrench, which is regularly tested during use, ensures the accuracy of the torque and operates in the correct tightening sequence. Main safety technical measures (1) The size of the wrench of the adjustable wrench should be consistent with the size of the nut, and the sleeve should not be added to the small wrench. A dead wrench should be used for high-altitude work. For example, when using an adjustable wrench, use a rope to fasten it, and people should fasten their seat belts. (2) When assembling the connecting bolts of steel components, it is strictly forbidden to insert your hands into the connecting surface or touch the screw holes. When picking and placing the bolster, your fingers should be placed on both sides of the bolster.
In mechanical devices, there are many ways to install and connect two components, such as bolt connection, welding, etc., but for installation and connection in a narrow space, such as the socket of two hollow cylinders with smaller diameters, due to the relatively small space It is very difficult to use this method, and it is extremely inconvenient to install and connect.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: connector screws, flat head full hexagonal sealed and closed pull nut, one rounded and one chamfered positioning pin, knurled shaft cylindrical pins and other products, we can provide products such as You have the right fastener solution for you.
