Service HotlineT-bolts are a common type of bolts that tend to be used with rails when used. When the existing rail is in use, the T-shaped bolts are easily stuck and cannot reach the designated position well, and the use is not convenient enough, so that the T-shaped bolts cannot be well fixed.
door cover structure with hidden screws includes a glass panel, an inner door cover, a computer board and a sealing strip, an adhesive bracket is adhered to the back of the glass panel, the inner door cover is fixedly connected with the adhesive bracket through screws, and the computer board is arranged on the glass panel. In the cavity formed by the panel and the inner door cover, the inner door cover is provided with a sealing slot, the sealing strip is embedded in the sealing slot, and the bottom of the sealing slot is provided with a mounting hole for the screw to pass through, and the glue The bracket is provided with a fixing hole matched with a screw thread, and the screw passes through the installation hole of the inner door cover and is threadedly connected with the fixing hole of the adhesive bracket, so as to fixedly connect the inner door cover and the glass panel. The screw is hidden in the sealing groove of the door cover, and is sealed with water through the sealing strip. The appearance is beautiful, easy to disassemble and assemble, and it can effectively protect the screw from rust.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a bayonet which is a T-shaped cylindrical pin with a misaligned through hole at the head, and a bayonet spring which is a ring-shaped spring steel wire whose ends are staggered. The retaining ring is clamped by the bayonet pin to fix the stop sleeve and the pin shaft together. A hydraulic excavator pin stopper with high disassembly and assembly efficiency and no need for a wrench. The technical solution of Guangdong Yueluo Hardware Industry Co., Ltd. is such that it includes a latch, a stop sleeve, a pin, a bayonet, and a circlip. The staggered end is clamped into the misaligned through hole of the plug, and screwed on the bottom of the stopper sleeve to fix the stopper sleeve and the pin shaft together. The latch is composed of a bayonet pin and a circlip, the circlip is screwed around the through hole of the bayonet pin to the root of the bayonet pin, and the stopper sleeve is tightly wrapped around the pin shaft, and the circlip is tightly against the bayonet pin. The head of the bayonet pin has two T-shaped cylindrical pins with staggered through holes, and the circlip is an annular spring steel wire whose ends are staggered. By adopting the pin shaft stopping method of the above technical scheme, it is extremely convenient and quick to disassemble and assemble the pin shaft. The bolt of Guangdong Yueluo Hardware Industry Co., Ltd. is only composed of a T-shaped cylindrical pin with two staggered through holes in the head and a ring-shaped spring steel wire with staggered ends. The structure is simple, convenient to manufacture, low cost and obvious. It is an excavator pin stop method with high disassembly and assembly efficiency, no need for a wrench and low manufacturing cost.
flat washer, an annular groove is formed on the outer side of the upper surface of the flat washer, and a sealing ring is embedded in the annular groove, at least five circularly equidistantly arranged cylinders are fixed on the upper surface of the flat washer, and the The upper surface of the flat washer is provided with a circular hole that communicates with its bottom, a collar is arranged in the circular hole, an upper circular ring is fixed above the collar, a lower circular ring is fixed below the collar, and the upper circular The diameter of the ring is the same as the diameter of the lower ring, the diameter of the collar is smaller than the diameter of the upper ring, the diameter of the collar is consistent with the diameter of the circular hole, and there are at least three equally spaced holes in the middle of the outer wall of the flat washer. A circular groove, the outer wall of the flat washer is fixed with at least three reinforcing blocks staggered with the circular groove, and the reinforcing blocks and the flat washer are welded into one piece.
Fasteners are an indispensable necessity in our lives and are used to flexibly fix two objects. However, in applications such as automobiles, large construction machinery and factories, the nuts often come loose and then fall off, resulting in frequent dangers and great dangers. Threats to people's lives and property.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: iron galvanized screws, yellow zinc high-strength screws, thickened slotted nuts, bakelite washers and other products, we can provide you with suitable products for you. Fastener Solutions.
