Service HotlineThe design of the existing shaft circlip is relatively simple, and the circlip is not fast enough to be fixed in the shaft groove. When the shaft circlip receives the repeated action of radial impact load, it is prone to loosening, which affects the use of the circlip.
The circlip is also called a retaining ring or a retaining ring. It is a kind of fastener and is installed in the shaft groove or hole groove of the machine and equipment to prevent the axial movement of the parts on the shaft or hole. The circlip includes an arc-shaped elastic bending portion and a circlip protrusion at the end of the elastic curved portion, and the circlip protrusion is provided with a small hole for matching with needle-nose pliers or circlip pliers. This part is a commonly used part on the equipment. Once the assembly is not in place, it will affect the overall performance of the equipment and cause safety hazards. At present, the most common assembly method is to manually clamp and deform the circlip with circlip pliers or needle-nose pliers, put the circlip into the annular groove of the inner hole of the end cover, and then release the needle-nose pliers or circlip pliers. . The assembly of the circlip is very troublesome, labor-intensive, and has low assembly efficiency. Once mass production is required, this process often becomes a bottleneck restricting production.
In the riveting operation, the rivet used is composed of a mandrel and a deformed collar. When in use, a through hole is drilled on the two components to be connected, and then the head of the rivet is passed through the through hole and clamped by a rivet. The tail of the rivet will break the rivet, the head of the rivet and the deformed collar remain in the through hole, and the whole riveting process is completed. The existing pull rivets have the following shortcomings: first, the parts where the pull rivet and the two components are connected cannot be completely and tightly fitted, which meets the requirements of non-sealing for parts that have waterproof and leak-proof requirements; second, the existing pull rivets The separation groove of the rivet mandrel is close to its head. When the mandrel is broken by the rivet during the riveting process, basically only the head of the mandrel remains in the deformation collar, and the connection of the two components depends on the deformation of the collar. Under the action of compressive stress, the inside of the deformed collar becomes hollow due to the breaking of the mandrel, and cannot bear large shear stress.
screw is a type of fastener that cooperates with threaded holes for combining various parts into one assembly and making the parts easy to assemble or disassemble. However, when the assembly containing the screw is used in a special environment, such as outdoor use or use in a liquid environment, there are requirements for preventing the leakage of liquid through the screw joint and preventing the screw from loosening at the screw joint. The screw structure does not have such a function. In the prior art, when there is a need for leakage prevention and loosening of the screw, a rubber washer is usually added between the screw head of the screw and the locking surface of the locked part, or the thread part of the screw is wrapped to prevent Leakage tape and then add anti-loose washers between the screw head of the screw and the locking surface of the locked part, so as to achieve the purpose of preventing leakage and loosening. However, the use of washers not only increases the thickness and weight of the assembly, but also requires an additional process during assembly, which is labor-consuming and labor-intensive. In the process of screwing, it is easy to cause uncertainty to the rubber washers due to the shear stress of the screws. Leakage occurs due to damage and deformation, and the practice of wrapping leak-proof tape around the screw teeth is often prone to damage to the threaded holes.
A T-bolt. This kind of bolt includes a bolt shank and a bolt head, and the bolt head adopts a special cylindrical bolt head, which can be suitable for installation and cooperation of various sizes. Although the shape of such a bolt head is greatly improved compared to the square bolt head in the prior art, the cylindrical bolt head is particularly inconvenient to install, and special installation tools must be used for installation. If the manual direct installation method is adopted, since the force area of the finger touching the side of the cylinder is small, it will increase the difficulty of the installation work and needs to be improved.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: blackened cylindrical head screws, copper screw caps, audio nuts, metric half-tooth screws and other products, we can provide you with suitable fastening for you piece solution.
