your location: 首页>>News>>Industry News

Service Hotline

+86760-8787 8587

Production of 304 stainless steel pitch non-standard hexagon thin nut hexagon nut hexagon screw

author:[email protected] Click:7966end source: time:2022-06-21 14:53:01

Summary of information:We have more than ten years of production experience in the screw industry, the main products are: round T-type nut, A-t...

The circlip is also called a retaining ring or a retaining ring. It is a kind of fastener and is installed in the shaft groove or hole groove of the machine and equipment to prevent the axial movement of the parts on the shaft or hole. The circlip includes an arc-shaped elastic bending portion and a circlip protrusion at the end of the elastic curved portion, and the circlip protrusion is provided with a small hole for matching with needle-nose pliers or circlip pliers. This part is a commonly used part on the equipment. Once the assembly is not in place, it will affect the overall performance of the equipment and cause safety hazards. At present, the most common assembly method is to manually clamp and deform the circlip with circlip pliers or needle-nose pliers, put the circlip into the annular groove of the inner hole of the end cover, and then release the needle-nose pliers or circlip pliers. . The assembly of the circlip is very troublesome, labor-intensive, and has low assembly efficiency. Once mass production is required, this process often becomes a bottleneck restricting production.

The quality of the combination screw should start with the screw wire of the combination screw manufacturer. The wire of the screw is the first hurdle to determine the quality of the combination screw. Even if the wire is not good, even if the production equipment is advanced and the staff is skilled, it is impossible to produce high-quality combination screws. In the second look at the quality of the combination screw products, from the overall aesthetics of the combination screw. A combined screw is formed, the size of the screw head, the superior appearance of the flat washer, whether the screw thread can pass the stop gauge, etc. These are all things that need to be detected. A good combination screw, its overall standard can meet the national standard requirements, or customer requirements. Finally, the quality of the combination screw product is seen from the color of the plating. Of course, the iron combination screw needs to be plated, but the stainless steel combination screw does not need it. Some of them are passivation at most, in order to increase the salt spray resistance of stainless steel combination screws. In the electroplating color of the combination screw, some of them are not well controlled, which will produce a great color difference. That doesn't look good.

In each maintenance, the newly replaced stud bolts and other accessories should be inspected. During the inspection, the focus should be on the head and guide part of the stud bolt. It is also necessary to strictly check that each part of the thread has No cracks or dents, also check the tooth shape of the studs for changes. Is there any abnormality in the thread pitch? If there is any abnormality, it must not be used again. A torque wrench should be used when installing the connecting rod cover. It must be tightened according to the specified standards, the torque should not be too large or too small, and attention should be paid to selecting the stud bolts and studs of the supporting manufacturer.

At present, injection molding screws are widely used in various electronic and automotive components, including a body, the middle of which is provided with a through hole 3, the body head 1 has a hexagonal cross-section, and the tail 2 is provided with screw teeth. When in use, the middle through hole 3 of the main body will first put the wire harness, and then fix it by injection molding from the head I, and the threads of the tail 11 should be connected and installed with other components. Because the head I of the main body is hexagonal, the torque provided after injection molding is insufficient. Therefore, after the external thread is installed and connected with other components, the head is prone to slip, the installation is not reliable, and there is no push-pull force, resulting in product failure and increased safety hazards.

Blind rivets (blind rivets) --------- rivet body (rivet body) mandrel (rivet stem or rivet mandrel). It is a type of rivet for single-sided riveting, but it must be riveted with a special tool - a rivet gun (manual, electric, pneumatic). When riveting, the rivet core is pulled by a special rivet gun to expand the rivet body and play a riveting role. This type of rivet is especially suitable for riveting occasions where it is inconvenient to use ordinary rivets (riveting from both sides), so it is widely used in construction, automobiles , ships, aircraft, machinery, electrical appliances, furniture and other products. Among them, the open-type oblate head blind rivets are the most widely used, the countersunk head blind rivets are suitable for riveting occasions where the surface needs to be smooth, and the closed blind rivets are suitable for riveting occasions that require high load and certain sealing performance.

We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat head hexagon, black carbon steel fine thread bolts, bowl-shaped concave-convex butterfly gaskets, drive-in expansion tension screws and other products, we can provide You have the right fastener solution for you.

Non-standard tooth pitch

Production of 304 stainless steel


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].