Service HotlineThe produced screws, due to unreasonable production aspects, are likely to cause quality problems in the screws. During production, many screw quality problems may be found upon delivery. Let's talk about the quality problems often encountered by screws and the reasons for the quality problems, and finally put forward some solutions. 1. The head of the screw is deformed and the head is crooked. The possible reasons are the poor installation of the first punch of the screw die and the improper adjustment of the machine. 2. The head of the screw is not round. The reason is that the selection of the first punch of the screw mold is improper or the first punch is not full enough. 3. The screw has burrs or burrs. The reason is the poor forming of one punch, mainly caused by too large gap between punch and die hole or too short punch. 4. The screw head is cracked and the screw head is cracked. The reason may be that there is a problem with the quality of the screw wire itself, so before the screw wire is headed, the quality department must check it and use the potion. Especially the stainless steel screw wire, it is necessary to check that it is stainless steel 201 and that is stainless steel 304. It is also possible that a die is used incorrectly (such as a die with a hexagonal washer head for a pan head), and the viscosity of the lubricating oil fails. For the problem of the screw head, you can read the article written by Manager Zhu above - high-strength screw fracture or head crack detection. In this article, some problems encountered by the screw head and how to detect the screw head problem are clearly introduced [4]. The common quality reasons for screws are of course more than the above, this is only part of it. There are other quality issues, then Manager Zhu will talk about it. The above screw quality reasons are for reference. If you encounter these problems, you can try the solutions proposed.
Guangdong Yueluo Hardware Industry Co., Ltd. relates to a square nut fastener for cable bridge installation, which is characterized in that it includes an upper plate body and a U-shaped jacket, and the upper plate body is provided with a downwardly protruding connecting cylinder, The two side plates of the U-shaped jacket are connected to the connecting cylinder, and the center line of the two side plates is located on the center line in the length direction of the upper plate body; the bottom of the U-shaped jacket is a wave-shaped elastic plate, which is a wave-shaped elastic plate It is fixedly connected on the two side plates, and the space enclosed by the two side plates of the U-shaped jacket, the wave-shaped elastic plate and the bottom of the connecting cylinder is the installation position of the square nut. Guangdong Yueluo Hardware Industry Co., Ltd. has a simple and reasonable structure, and is extremely convenient and flexible to operate; it does not occupy the bottom space of the C-shaped steel after installation, which increases the variety of installation, and can be applied to square nuts of different thicknesses, and the installation is firm.
lead screw nut is provided with a through hole in the center for the screw rod to pass through, the surface of the through hole is provided with a screw thread engaged with the thread on the outer surface of the screw rod, and the surface of the through hole of the lead screw nut is provided with a thread along the surface of the through hole. The oil storage groove in the axial direction, the depth of the oil storage groove is greater than the depth of the thread.
The four corners of the bolt head of the traditional T-slot connection bolt are all rounded corners, which will make the contact area between the bolt and the T-slot too small and reduce the connection fastness, especially when used for connection. When aluminum or copper profiles are used, due to the low hardness of the material, it is more likely to cause deformation of the T-shaped groove and affect the connection effect. Furthermore, since the traditional T-bolt has no direction indicator, it is difficult for the installer to identify the installation state during installation.
Standard parts are commonly used parts, which are widely used in various mechanical structures. Among them, the T-track bolt is a common standard part. The existing T-shaped track bolts, especially those used in high-speed railways, are often installed in pre-buried tracks, and the T-shaped track bolts are not easy to install, which may easily cause positional deviation.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: solid positioning cylindrical pins, black 8.8 high-strength hexagonal nuts, non-standard special bolts for cutting parts, pins with holes and other products, we can provide you with products such as Provide the right fastener solution for you.
