Service HotlineThe purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a bayonet which is a T-shaped cylindrical pin with a misaligned through hole at the head, and a bayonet spring which is a ring-shaped spring steel wire whose ends are staggered. The retaining ring is clamped by the bayonet pin to fix the stop sleeve and the pin shaft together. A hydraulic excavator pin stopper with high disassembly and assembly efficiency and no need for a wrench. The technical solution of Guangdong Yueluo Hardware Industry Co., Ltd. is such that it includes a latch, a stop sleeve, a pin, a bayonet, and a circlip. The staggered end is clamped into the misaligned through hole of the plug, and screwed on the bottom of the stopper sleeve to fix the stopper sleeve and the pin shaft together. The latch is composed of a bayonet pin and a circlip, the circlip is screwed around the through hole of the bayonet pin to the root of the bayonet pin, and the stopper sleeve is tightly wrapped around the pin shaft, and the circlip is tightly against the bayonet pin. The head of the bayonet pin has two T-shaped cylindrical pins with staggered through holes, and the circlip is an annular spring steel wire whose ends are staggered. By adopting the pin shaft stopping method of the above technical scheme, it is extremely convenient and quick to disassemble and assemble the pin shaft. The bolt of Guangdong Yueluo Hardware Industry Co., Ltd. is only composed of a T-shaped cylindrical pin with two staggered through holes in the head and a ring-shaped spring steel wire with staggered ends. The structure is simple, convenient to manufacture, low cost and obvious. It is an excavator pin stop method with high disassembly and assembly efficiency, no need for a wrench and low manufacturing cost.
When using a rivet nut, drill a hole corresponding to the outer diameter of the rivet nut on the thin wall, then place the rivet nut on the bolt of the special rivet gun, push the handle to screw in the rivet nut, and put it into the drilled hole. In the workpiece, squeeze the handle, the rivet nut expands, and the deformed skirt bulges and deforms. At this time, the workpiece is tightened. After riveting, the handle is pulled out, the bolt is released from the rivet nut, and the corresponding screw is screwed into the rivet nut threaded hole. , forming a tight riveted body.
According to the force of the connection, it is divided into ordinary and hinged holes. According to the shape of the head: there are hexagonal head, round head, square head, countersunk head and so on. Among them, the hexagonal head is the most commonly used. Generally, countersunk heads are used where connections are required. [1] The English name of the riding bolt is U-bolt. It is a non-standard part. The shape is U-shaped, so it is also called a U-bolt. There are threads on both ends that can be combined with nuts. It is mainly used to fix tubular objects such as water pipes or sheets such as The leaf spring of a car is called a horse-riding bolt because it fixes the object in the same way that a person rides on a horse. According to the length of the thread, it is divided into two categories: full thread and non-full thread. [2] According to the thread type, it is divided into two types: coarse thread and fine thread. The coarse thread is not displayed in the bolt mark. The bolts are divided into eight grades: 3.6, 4.8, 5.6, 6.8, 8.8, 9.8, 10.9, and 12.9 according to their performance grades. Among them, the bolts above grade 8.8 (including grade 8.8) are made of low-carbon alloy steel or medium-carbon steel and are heat-treated (quenched). + Tempering), commonly known as high-strength bolts, and below grade 8.8 (excluding 8.8) are commonly known as ordinary bolts. [2] Ordinary bolts can be divided into three grades: A, B, and C according to the production accuracy. Grades A and B are refined bolts, and grade C is rough bolts. For connecting bolts for steel structures, unless otherwise specified, they are generally ordinary rough grade C bolts. There are differences in the processing methods of different grades. Usually the corresponding processing methods are as follows: ① The bolts of grade A and B bolts are processed by lathes, with smooth surfaces and accurate dimensions. High, rarely used; ②C-grade bolts are made of unmachined round steel, the size is not accurate enough, and its material property grade is 4.6 or 4.8. The deformation is large during shear connection, but the installation is convenient and the production cost is low. It is mostly used for tensile connection or temporary fixation during installation. [2]
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a low-carbon steel rivet nut fastener, which can be easily fixed on a thin wall without welding, easy to operate, firm riveted, and suitable for single-sided riveting.
The positioning pin is a pin designed to accurately position the two adjacent parts of the mold in a mold composed of two or more parts. It can be seen that the positioning pin plays a positioning role, and the mold must be accurately synchronized when it is closed. product, and the positioning pin can make the upper and lower molds play a role in accurate positioning. In the mold design and manufacture of Yueluo, the positioning pin is one of the most common parts. Since it is only used for positioning between parts, few people will pay too much attention to it. In the cold stamping process of Yueluo, the dimensional accuracy of the blanking parts depends on the size of the working part of the punch and the concave die, and the dimensional difference between them constitutes the blanking die gap. Gap is an important process parameter for die design, and its size has a great influence on the quality of the section of the blanking part, the blanking force, and the life of the die. If the gap is too large, punching burrs will appear in punching; if the gap is too small, secondary cracks will occur in the section and extrusion burrs will appear, which will make the quality of the section after punching unsatisfactory, and a reasonable gap will not only help the punching section. The improvement of the quality also contributes to the improvement of the lifespan of the 7-pack.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: automotive tire nuts, 12.9 cylinder head screws, JB4364 screws, thin fine pitch hexagon nuts and other products, we can provide you with suitable fasteners solution.
