Service HotlineRelated Specifications of Automobile Welding Nuts (Square Nuts) Serial Number Standard Number Name (English) Name (Chinese) Remarks 1 MS440014 NUT,WELD Welding Square Nut M8 2 MS440013 NUT,WELD (6) Welding Square Nut M6 3 MF445605 NUT,WELD (10 ) welding square nut M10 4 MU442002 NUT,WELD welding square nut M6 parking brake handle 5 MB077464 NUT,WELD welding square nut for seat belt welding square nut 6 MB040348 BOLT WELD (10X22) welding bolt M10×22, bearing surface 7 MF198353 BOLT,WELD (6X14) Weld bolt M6×14, end face 8 MR236366 NUT (12) Nut M12 Suspended trailing arm mount 9 MS440015 NUT,WELD (10) Weld square nut M10 10 PW832525 BOLD WELD 7/16 UNF Weld bolt 7/16 For seat belt, bearing surface 11 MB528563 STUD,WELD Welding stud M6×20 12 MS440066 NUT,WELD (5/16=18UNC) Welding square nut 5/16 Child safety system 13 MS440018 NUT, WELD (6) Welding square nut M6 14 MF198375 BOLT,WELD (8X30) Welding stud M8×30 15 MF198038 BOLT, WELD (6X25) Welding bolt M6×25, bearing surface 16 MR236467 NUT (12) Welding square nut M12, for engine mount 17 MF140024 BOLT, FLANGE (8X18) Hexagon flange bolt without 3D 19 MF198036 BOLT,WELD (6X20) Weld stud M6×20 20 MF198034 BOLT,WELD (6X16) Weld bolt M6×16, bearing face 21 MS440012 NUT,WELD (5) Weld Square Nut M5 22 MB343340 BOLT,WELD (8X26) Welding Bolt M8×26, Bearing Surface 23 MB138471 STUD,WELD Welding Stud M8×46, Bearing Surface 24 MS190066 BOLT,WELD (8X16) Welding Bolt M8×16, Bearing Surface, NO 3D 25 MS240145 BOLT,WASHER ASSEMBLED (8X20) BOLT AND WASHER ASSEMBLY NO 3D 26 MB281149 NUT,WELD(6) WELD BOLTS M8, NO THREADS REQUIRED FOR BEARING 27 MF445603 NUT,WELD (6) Welded square nut M6 Reinforcing plate for rear door lock 28 MS190068 BOLT,WELD (8X20) Welded bolt M8×20, bearing surface 29 MU431507 NUT,WELD Welded square nut M8 for door hinge installation 30 MS240121 BOLT,WASHER ASSEMBLED (6X16) Bolt and washer assembly M8 for fuel filler cap 31 MS100221 BOLT,FLANGE (6X12) Flange face bolt M6 for fender mounting 32 MB344675 STUD,WELD Weld stud M6×10
It is used for fastening in the machinery, construction and electrical industries. One end is a hexagonal head for wrench tightening, and the other end is a thread. According to different thread lengths, it is divided into full thread and half thread, abbreviated as: GB bolt.
A screw suitable for a variety of tools is a single-structure threaded part, including a screw body and a screw head. The outer surface of the screw body is processed with an external thread 1, and the outer side of the screw head is formed by six screw heads. Prismatic, the top surface of each edge of the outer hexagonal prism is a boss, between each boss is an end face groove 4, and the middle of each boss is provided with an end face hole 3; the inner side of the screw head is formed by six screw heads. The side surface 5 forms an inner hexagonal prism hole, and the bottom of the inner hexagonal prism hole is processed with a cross groove 10 .
In the process of electronic accessories such as mobile phones and computers, especially multi-layer circuit boards, there are generally fixed connections between multi-layer circuit boards or other components. At present, there are two main connection methods. One is to use laser welding. However, the laser welding equipment is expensive and has very high requirements on the position of the weldment. Therefore, during welding, it must be ensured that the final position of the weldment needs to be the same as the laser beam will impact. Solder joint alignment. The other is to use a metal rivet to pass through the positioning hole, and then impact the rivet with a punching needle, so that the open end of the rivet is deformed and opened and pressed on the fixed piece to form a rivet fixed state. However, in actual operation, when the open end of the rivet tube is opened and deformed by the impact, strong cracking often occurs, resulting in a small amount of conductive fracture debris, which falls on the circuit board or other devices to be connected, causing Short circuit, in view of this shortcoming, some manufacturers have changed the metal rivets to plastic materials, but the plastic rivets have poor ductility and often break when impacted with a punching needle, resulting in the failure to achieve the riveting fixing force of the original metal rivets. In addition, the above two fixing methods are complicated in operation and low in installation efficiency.
Inspection method There are two types of screw surface inspection, one is the inspection before the screw is produced and not plated, and the other is the inspection after the screw is plated, that is to say, after the screw is hardened and the surface of the screw is treated. . After the screws are produced and before electroplating, we inspect the screws in various aspects such as size and tolerance. See if there are national standards or customer requirements. After the surface treatment of the screws, we will inspect the plated screws, mainly to check the color of the plating and whether there are any broken screws. In this way, when we deliver screw goods to customers, customers can successfully pass the customs when they receive the goods. Inspection of screws after treatment: 1. Appearance quality requirements The inspection of the appearance of screws is carried out from the aspects of appearance, electroplating layer and so on. Second, the inspection of the thickness of the screw coating 1. The measuring tool method uses a micrometer, a vernier caliper, a plug gauge, etc. 2. Magnetic method The magnetic method is used to measure the thickness of the coating layer, which is a non-destructive measurement of the non-magnetic coating layer on the magnetic substrate with a magnetic thickness gauge. 3. Microscopy Microscopy is called metallographic method, which is to magnify the etched fasteners on a metallographic microscope with a micrometer eyepiece to measure the thickness of the coating on the section. 4. Timing flow method The timing flow method uses a solution that can dissolve the coating to flow on the local surface of the coating, and calculates the thickness of the coating according to the time required for the local coating to dissolve. There are also coating drop method, anodic dissolution Coulomb method, etc. 3. Inspection of the adhesion strength of the screw coating There are many methods for evaluating the adhesion between the coating and the base metal, usually the following. 1. Friction polishing test; 2. File method test; 3. Scratch method; 4. Bending test; 5. Thermal shock test; 6. Extrusion method. 4. Inspection of corrosion resistance of screw coatings The corrosion resistance inspection methods of coatings include: atmospheric exposure test; neutral salt spray test (NSS test); acetate salt spray test (ASS test), copper accelerated acetate salt spray test (CASS) test); and corrosion paste corrosion test (CORR test) and solution spot corrosion test; immersion test, inter-dipping corrosion test, etc.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat head hexagon socket head screws and nuts, round head Phillips screws, external hexagon half-tooth screws, joint lifting ring bolts and other products, we can provide you with suitable products. Your fastener solution.
