Service HotlineThe positioning pin is a pin designed to accurately position the two adjacent parts of the mold in a mold composed of two or more parts. It can be seen that the positioning pin plays a positioning role, and the mold must be accurately synchronized when it is closed. product, and the positioning pin can make the upper and lower molds play a role in accurate positioning. In the mold design and manufacture of Yueluo, the positioning pin is one of the most common parts. Since it is only used for positioning between parts, few people will pay too much attention to it. In the cold stamping process of Yueluo, the dimensional accuracy of the blanking parts depends on the size of the working part of the punch and the concave die, and the dimensional difference between them constitutes the blanking die gap. Gap is an important process parameter for die design, and its size has a great influence on the quality of the section of the blanking part, the blanking force, and the life of the die. If the gap is too large, punching burrs will appear in punching; if the gap is too small, secondary cracks will occur in the section and extrusion burrs will appear, which will make the quality of the section after punching unsatisfactory, and a reasonable gap will not only help the punching section. The improvement of the quality also contributes to the improvement of the lifespan of the 7-pack.
1. When the main body is large-scale equipment, accessories need to be installed, such as sight glass, mechanical seal seat, deceleration frame, etc. The stud bolts used at this time, one end is screwed into the main body, and the other end is equipped with nuts after the accessories are installed. , Since the accessories are often disassembled, when the main body and the accessories are directly connected by bolts, the main body threads will be worn or damaged over time, and it is very convenient to use studs to replace them. 2. When the thickness of the connecting body is very large and the bolt length is very long, stud bolts will be used. The purpose of anti-loosening of stud connection In actual work, the external load has vibration, change, high temperature creep of the material, etc., which will reduce the friction force, the positive pressure in the thread pair disappears at a certain moment, and the friction force is zero, thus making the threaded connection loose. , if repeated action, the threaded connection will loosen and fail. Therefore, it is necessary to prevent loosening, otherwise it will affect the normal work and cause accidents.
The circlip lifting and tightening mechanism includes a lifting mechanism and a tightening mechanism; the lifting mechanism includes a lifting cylinder and a ball screw; the output shaft of the lifting cylinder is connected with the ball screw; the ball screw drives the tightening mechanism to achieve up and down move; the tightening mechanism includes a tightening motor, and the output shaft of the tightening motor drives a pinion sleeved on the output shaft to rotate; the pinion drives the largest gear meshed with it to rotate, and the largest gear is driven by The second largest gear meshed with it rotates; the diameter of the first largest gear is the same as that of the second largest gear; the lower ends of the rotating shafts of the first largest gear and the second largest gear are equipped with rotating discs, and each rotating disc is fixedly installed A probe; two probes can be inserted into the two holes of the circlip at the same time, and the circlip can be tightened or loosened as the motor rotates.
3. Friction coefficient The friction angle is an important factor affecting the torque, and the existence of friction is the basis for the normal operation of the lock nut. When the lock nut is working, the contact surface has pressure and friction under the action of the elastic restoring force of the thread piece. During the repeated use, the rough position and edges and corners of the contact surface are ground and smoothed under the action of cyclic friction. The coefficient of friction becomes smaller, which in turn reduces the maximum unscrewing torque of the nut.
In the non-standard mechanical design, when the middle part of the long shaft or rod-shaped structure needs to be threaded, the end is limited and the nut cannot be penetrated, which will cause the problem that the installation cannot be realized. In order to solve this problem, it often has to be cancelled. It is not conducive to the realization of equipment cost reduction and optimal function, and even the problem cannot be solved, and another way out is needed.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: A-grade small flat washers, full-thread threaded rods, hand-tightened disc bolts, 4.8-grade hexagonal nuts and other products, we can provide you with suitable products for you. Fastener Solutions.
