Service HotlineThe working principle of the nut is to use the friction between the nut and the bolt for self-locking. However, the reliability of this self-locking is reduced under dynamic loads. In some important occasions, we will take some anti-loosening measures to ensure the reliability of the nut locking. Among them, the use of lock nuts is one of the anti-loosening measures. There are also two types of locking nuts. One is to use two identical nuts to screw on the same bolt, and a tightening torque is added between the two nuts to make the bolt connection reliable. The other is a special lock nut, which needs to be used together with a lock washer. As shown in FIG. 1, a plastic gasket 2 is arranged in the center of the nut 1 to play a locking effect, but the process is complicated and the production is inconvenient. One is to drill through threaded holes from the outer surface of the nut to the inner thread surface (usually 2, distributed at 90 on the outer surface), which are used to screw in small-diameter countersunk head screws. The purpose is to apply a thread to the thread. A centripetal force prevents the lock nut from loosening. At present, the lock nut with better quality on the market is inlaid with small copper pieces that are consistent with the thread of the lock nut on the inner surface of the nut, which is used to prevent the radial jacking screw from directly contacting the locked thread and being damaged. By. This kind of lock nut is gradually applied in the shaft end locking of rotating motion parts, such as the anti-looseness of the bearing at the mounting end of the ball screw. The process is equally complex.
At present, for roller or needle roller bearings without cages, ribs, and low-speed operation, the structure mainly includes inner and outer rings and rollers or needle rollers in the raceway between the inner and outer rings, and additional The retaining rings on both sides of the roller or needle roller, among which the retaining rings added on both sides of the roller or needle roller are annular steel sheets punched from metal sheet, and their function in the bearing is only Correctly guide the rollers or needle rollers to run normally in the raceway between the inner and outer rings to prevent the rollers or needle rollers from deviating and slipping out of the raceway. The defect of the retaining ring of this structure is that first, because the rigid retaining ring and the inner ring are completely separated, there is a gap between the retaining ring and the installation shaft during installation. When the bearing is working, The retaining ring is driven by the outer ring and the rollers or needle rollers to rotate around the installation shaft. Due to the inconsistency of the structure, the retaining ring is easy to fall off during the rotation process, the safety of use is poor, and the rollers or needle rollers will appear toward the raceway. The situation of one side offset, which causes the bearing load center to offset, affects the reliability of the bearing operation, and ultimately affects the service life of the bearing; There is a gap between the raceways of the needle, so the tidbits, dust, etc. generated during the working process will continue to enter the raceway between the inner and outer rings. It is stuck; in addition, due to the gap between the steel retaining ring and the raceway, the grease stored in the raceway will be continuously lost, which will cause the bearing to heat up due to frequent lack of grease, or even burn out, which also affects the to the service life of the bearing.
1. When the main body is large-scale equipment, accessories need to be installed, such as sight glass, mechanical seal seat, deceleration frame, etc. The stud bolts used at this time, one end is screwed into the main body, and the other end is equipped with nuts after the accessories are installed. , Since the accessories are often disassembled, when the main body and the accessories are directly connected by bolts, the main body threads will be worn or damaged over time, and it is very convenient to use studs to replace them. 2. When the thickness of the connecting body is very large and the bolt length is very long, stud bolts will be used. The purpose of anti-loosening of stud connection In actual work, the external load has vibration, change, high temperature creep of the material, etc., which will reduce the friction force, the positive pressure in the thread pair disappears at a certain moment, and the friction force is zero, thus making the threaded connection loose. , if repeated action, the threaded connection will loosen and fail. Therefore, it is necessary to prevent loosening, otherwise it will affect the normal work and cause accidents.
The more complex inlaid embedded copper nut copper insert nut specification is M8, this copper insert nut is embedded in the injection molded part of the car, 5 twill embossing, 4 left twill embossing, 1 right twill embossing Knurling. Since there are multiple rolling patterns, double tool rests + double embossing rests are used, and 5 grooves and 2 chamfers are inserted at one time by a widening forming knife. The hot-pressed copper insert nut contains Reticulated and straight lines, the outer circle is conical, in the process of hot pressing to facilitate smooth introduction into the plastic hole.
⑥ Surface Treatment Zn: White Zinc C: Color Zinc B: Blue Zinc F: Black Zinc O: Black Oxide Ni: Nickel Cu: Bronze Br: Red Copper P: Phosphating
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: Phillips bolts, left-hand left-hand reversed nuts, black nickel-plated screws, gear nuts and other products, we can provide you with fastening suitable for you. piece solution.
