Service HotlineA rivet is a nail-shaped object with a cap on one end: in riveting, the parts being riveted are joined by their own deformation or by interference. There are many types of rivets, and they are informal. However, the two ends of conventional rivets are concentric, which is not suitable for special occasions.
screw is a type of fastener that cooperates with threaded holes for combining various parts into one assembly and making the parts easy to assemble or disassemble. However, when the assembly containing the screw is used in a special environment, such as outdoor use or use in a liquid environment, there are requirements for preventing the leakage of liquid through the screw joint and preventing the screw from loosening at the screw joint. The screw structure does not have such a function. In the prior art, when there is a need for leakage prevention and loosening of the screw, a rubber washer is usually added between the screw head of the screw and the locking surface of the locked part, or the thread part of the screw is wrapped to prevent Leakage tape and then add anti-loose washers between the screw head of the screw and the locking surface of the locked part, so as to achieve the purpose of preventing leakage and loosening. However, the use of washers not only increases the thickness and weight of the assembly, but also requires an additional process during assembly, which is labor-consuming and labor-intensive. In the process of screwing, it is easy to cause uncertainty to the rubber washers due to the shear stress of the screws. Leakage occurs due to damage and deformation, and the practice of wrapping leak-proof tape around the screw teeth is often prone to damage to the threaded holes.
Basic requirements for the installation of T-bolt sleeve components: only when the T-head and the middle slot of the anchoring plate are in good agreement and the anchoring surfaces are in close contact, can the force be evenly applied. If the T-head and the anchoring plate are in line contact, even only point contact , the bolt is partially stressed, which will seriously affect the life. Therefore, the verticality of the sleeve installation must be less than or equal to 1/1000, that is, the horizontality of the anchoring plate surface must be less than or equal to 1/1000, and the center deviation of the sleeve must be controlled within 5mm (the center deviation of the T-bolt is 2mm). Therefore, improving the embedded accuracy of the T-bolt sleeve is the key to the installation of the T-bolt integral sleeve.
In order to solve the problem of nut loosening, various self-locking nuts have appeared, which have complex structure, high production cost, inconvenient installation and unsatisfactory anti-loosening effect. At present, the never-loosening nuts produced in Japan are mostly used, mainly in the form of double nuts. Each nut is provided with an eccentric cam protrusion, and each nut is provided with a groove and an inclined plane to squeeze the cam protrusion of each nut. When pressing, the cam protrusion of the nut will move to a small radius along the slope of the nut, so that the nut will not loosen, but whether it is a nut or a nut, it is always under the action of eccentric force. In addition, various non-loose nuts designed by many manufacturers are to increase the friction between the nut and the fastening workpiece or increase the barb to achieve the purpose of never loosening, but the effect is not ideal.
An asphalt pavement screw, the asphalt pavement screw includes a main rod, an outer jacket, a pressing piece and a nut, the main rod is a columnar rod, the lower end of the main rod is provided with a table for supporting the outer jacket, and the middle part of the main rod passes through the outer jacket The upper part of the main rod is provided with a threaded section, the pressing piece and the nut are set on the threaded section, and at least two deformation holes are provided on the outer sleeve, and the middle part of the deformation hole is larger than the upper and lower sides of the deformation hole, The part between the adjacent deformation holes is the deformation part, and the width of the middle part of the deformation part is smaller than the width of the upper and lower sides of the deformation part. After the asphalt pavement screw of Guangdong Yueluo Hardware Industry Co., Ltd. is assembled, it has strong bonding force with the asphalt road. Even if it is hit, it will not be separated from the asphalt road. Using this asphalt pavement screw to fix the road railing can strengthen the road railing. The firmness of the assembly.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: internal and external teeth without intermediary nuts, flange lock nuts, full threaded bolts, stainless steel countersunk head screws and other products, we can provide you with suitable products for you. Fastener Solutions.
