Service HotlineThe utility model relates to a connecting piece, in particular to a female and female screw used for shaping products in interior decoration. In the current decoration project, when fixing the decoration stereotyped product, the process is complicated, so labor-intensive and time-consuming, the construction cost is high, and the construction degree is low. For example, the decorative board for fixing the wall, the main process step used in its operation is the leveling of the nail strip. That is to say, saw the wood to the required specifications, then draw horizontal and vertical lines on the wall, and then nail the wooden strips to the wall according to the horizontal and vertical lines, and then glue and glue the board. The first step is to install the lines, color and paint. It can be seen that it is quite troublesome to use the above method to construct. The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a female screw, which can skillfully connect decorative products to the wall. As conceived above, the technical solution of Guangdong Yueluo Hardware Industry Co., Ltd. is a female screw, which is characterized in that both ends of the screw are threaded, the screw-in end is screwed into the plastic expansion tube inserted into the wall, and the other end of the screw is threaded with the same A female piece is mated and connected. The other end of the screw can also be barb-shaped and directly fit with the decorative board. The screw thread of the screw-in end is a wood thread, and the thread of the mating connection end with the female part is a machine thread.
The flat key transmits torque on the side, has good neutrality, is easy to assemble and disassemble, and cannot realize the axial fixation of the parts on the shaft. Ordinary flat key: Type A, Type B, Type C, Type A is used for shaft grooves machined by end mills. The key is well fixed axially in the groove, but the stress concentration caused by the groove on the shaft is large; Type B is used for disc milling cutters. The machined shaft groove, the stress concentration of the shaft is small; the C type is used for the shaft end; it is suitable for high-speed, high-precision or occasions under variable load and impact, such as fixing gears, sprockets and other rotating parts on the shaft. Guided flat key: The key is fixed on the shaft with a screw, the key and the hub groove are in dynamic fit, and the parts on the shaft can move axially. For the convenience of starting the key, there is a key-starting screw hole. Use the occasions where the axial movement of the parts on the shaft is not large, such as the slip gear in the gearbox. Feather key: The key is fixed on the axle, and the parts on the shaft can move axially with the key; it is used in the occasions where the axial movement of the parts on the shaft is large;
Equipment that needs to be maintained at high altitude or under complex working conditions requires screw loss prevention design. Although traditional captive screws can achieve the purpose of preventing falling off, because the diameter of the screw is smaller than the major diameter of the thread, it is difficult to match the gasket, and the gasket will be eccentric, which is easy to install. Scratch the surface of the product, affecting the corrosion resistance and appearance of the product.
In the process of our transformation and upgrading from big manufacturing to strong manufacturing, the talents of the main body of innovation play an important catalytic role, including a large number of engineers, and drawings are a necessary expression tool for their practical innovation. Engineering drawing courses, as the basic courses of engineering colleges, play an important role in students' ability to read and output engineering drawings, and are directly related to the innovation ability in future work practice.
In industrial production, some products need to remove the fixing screws; or in the assembly line, the screws that fix the product on the fixture also need to be removed when the product is unloaded. At present, the dismantling of the screws is mainly completed by the manual operation of the operator. However, this method of manually dismantling the screws has low work efficiency and high production cost.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: 20 type 30 type 40, wire lug gaskets, flat head vertical rivet nuts, water heater screws and other products, we can provide you with suitable products for you. Fastener Solutions.
