Service HotlineWith the continuous improvement of road facilities, guardrails are set up in the middle of the roads in most cities at the separation of the upper and lower lanes. At the same time, guardrails are also set up between the motor vehicle lane and the non-motor vehicle lane. The bottom of the guardrail column is set with a base, and the base is usually made of If the steel nail is fixed, the deformation hole should be drilled on the asphalt road first, and then the steel nail should be knocked into the deformation hole. Because the outer wall of the steel nail is cylindrical, the friction force on the ground is small, and the guardrail is affected by the deformation. When the external impact force occurs, the steel nails are easily detached from the asphalt road, making the road guardrail lose its fixation. In some places, expansion screws are used to fix the railings, but during the tightening process of the expansion screws, the expansion pieces are opened by the force of the ejector rod, and the opening angle is small. Limited, the railing will still fall down when subjected to a large impact. Therefore, it is necessary to design a special screw for fixing the railing on the asphalt road.
Sprinkle the excess standard spring washer 7 on the positioning plate 12-1 on the spring washer positioning plate 2, and shake the spring washer positioning plate 2 by hand. After a short time, the spring washer 7 will be positioned and arranged on the upper positioning plate 12-1. In the upper spring washer hole 2-7, since the width of the opening groove 12-32 of the baffle plate 12-3 is smaller than the diameter of the spring washer hole 2-7, and the thickness of the upper positioning plate 12-1 is designed according to the thickness of the spring washer 7, Only one spring washer 7 can be accommodated in the spring washer hole 2-7 of each upper positioning plate 12-1, and the excess spring washer 7 is cleaned with a brush.
screw with a gasket aims to provide a screw with a gasket that improves installation efficiency. The technical solution of the screw is that after the screw cap, the connecting rod and the screw rod are processed, the gasket with the installation through hole is processed. The installation through hole is drilled through the connecting rod, and then the end of the screw rod opposite to the connecting rod is processed to form a convex tooth structure by extrusion. At the same time, the outer diameter of the tooth peak of the convex tooth is larger than the inner diameter of the installation through hole, so that the gasket is not easy to be installed. Falling off, the step of manually wearing the gasket is reduced, that is, the workload of the staff is reduced, and the installation efficiency is relatively high. The flange increases the contact area between the screw cap and the gasket, and enhances the friction between the screw cap and the gasket, which can prevent the screw from loosening easily after being fastened and installed, thereby improving the connection stability of the screw. When installing the screw, the fixing part can be snapped into the fixing groove on the installation plane, so as to avoid the washer from rotating with the rotation of the screw when the screw is tightened, which is convenient for the tightening and installation of the screw.
As we all know, when installing the outdoor unit of the air conditioner, most of the installers need to hang it on the outer wall. When tightening the machine foot screws, they all need to lean out of the window or climb out the whole person, and use a wrench to tighten it. . Therefore, it is difficult for the installer to operate, and it is easy to drop the installation materials such as screws and nuts, which is not only a waste of materials, but also easy to hurt personnel. The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to solve the above problems, and provide a safe and labor-saving air conditioner outdoor unit machine foot screw installer that the installer does not have to lean out of the window or climb out of the room, and the installation materials are not easy to fall.
At present, in the production workshop, there is no special tool for removing rivets such as skew, wrong rivets, and multiple rivets. When removing these rivets, workers use homemade rivet removal tools, use a sledgehammer to remove the rivet head, and then use a sharp tool to remove the rivet rod. eject. During the removal operation, sometimes the rivet head will fly out, the speed is high, the danger is extremely high, and the labor intensity is high, which has caused many industrial accidents.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: single-head hexagon stud bolts, paint rivets, self-tapping self-drilling screws, 201 cylinder head screws and other products, we can provide you with products suitable for you fastener solutions.
