Service HotlinePeople often think that magnets attract stainless steel to verify its pros and cons and its authenticity. If it does not attract non-magnetism, it is considered to be good, and it is genuine; if it is magnetic, it is considered to be counterfeit. In fact, this is an extremely one-sided, unrealistic and wrong identification method. There are many kinds of stainless steel screws, which can be divided into several categories according to the organizational structure at room temperature: 1. Austenite type: such as 304, 321, 316, 310, etc.; 2. Martensite or ferrite type: such as 430, 420, 410, etc.; Austenite type is non-magnetic or weakly magnetic, and martensite or ferrite is magnetic. Most of the stainless steel usually used for decorative tube sheets is austenitic 304 material, which is generally non-magnetic or weakly magnetic, but may also appear magnetic due to fluctuations in chemical composition or different processing conditions caused by smelting, but this cannot be considered as a Counterfeit or substandard, what is the reason for this? As mentioned above, austenite is non-magnetic or weakly magnetic, while martensite or ferrite is magnetic. Due to component segregation or improper heat treatment during smelting, a small amount of martensite or ferrite in austenitic 304 stainless steel will be caused. body tissue. In this way, 304 stainless steel will have weak magnetism. In addition, after cold working of 304 stainless steel, the structure will also be transformed into martensite. The greater the cold working deformation, the more martensite transformation, and the greater the magnetic properties of the steel. Like a batch of steel strips, Φ76 tubes are produced without obvious magnetic induction, and Φ9.5 tubes are produced. The magnetic induction is more obvious due to the large deformation of the bending and bending. The deformation of the square rectangular tube is larger than that of the round tube, especially the corner part, the deformation is more intense and the magnetic force is more obvious. In order to completely eliminate the magnetic properties of 304 steel caused by the above reasons, the stable austenite structure can be restored by high-temperature solution treatment, thereby eliminating the magnetic properties. In particular, the magnetic properties of 304 stainless steel caused by the above reasons are completely different from those of other materials such as 430 and carbon steel, which means that the magnetic properties of 304 steel always show weak magnetic properties. This tells us that if the stainless steel strip is weakly magnetic or completely non-magnetic, it should be judged as 304 or 316 material; if it is the same as carbon steel, it shows strong magnetism, because it is judged as not 304 material.
M4 grounding screw used to fix the grounding wire on household appliances and other equipment, the stud is cylindrical, and the thread is perpendicular to the end (section) surface. However, the screw holes on the equipment all have tapping guide grooves for sinking and guiding due to the manufacturing process requirements. When fixing the ground wire, if the screw is not positioned accurately (the screw is inclined), the screw is pressed down hard, which is easy to cause the screw and the screw. The screw hole bites the teeth, and after biting the teeth, it is easy to cause the screw to loosen or fall off, posing a safety hazard.
1) Scope This standard specifies the lock nut (referred to as nut), the size of the locking device, technical requirements, acceptance rules and measurement methods. This standard applies to the design, production, inspection and user acceptance of nuts and locking devices for tapered bushings. 2) Terminology The terms used in this standard conform to the provisions of GB/T 6930. This standard specifies the marking system, index, test method and marking of the mechanical and working performance of the effective torque section steel hexagonal lock nut. This standard is applicable to coarse thread 6H class nuts made of carbon steel or alloy steel, the width across the sides conforming to the provisions of GB 3104, the nominal height is ≥ 0.8D, and the guaranteed load and effective torque need to be specified, and the thread diameter is 3 ~ 39mm. Except for the effective torque part, the thread size and tolerance are specified in GB 193, GB 196 and GB 197. The working temperature range of the nut should be in accordance with: All-metal nut without electroplating treatment: -50℃～+300℃. All-metal nuts with electroplating treatment: -50℃～+230℃; nuts embedded with non-metallic elements: -50℃～+120℃. This standard does not apply to nuts with special performance requirements (such as weldability and corrosion resistance). For stainless steel and non-ferrous metals with fine pitch lock nuts or thin nuts made of carbon steel or alloy steel, the performance indicators and test methods of effective torque specified in this standard may be adopted by mutual agreement.
Rivets are usually used for riveting the connection between objects, and usually require the use of specific special tools to operate. There are many types of rivets, such as round head rivets, flat cone head rivets, countersunk head rivets, half countersunk head rivets, flat head rivets, hollow rivets, tubular rivets, sign rivets, etc. in order to meet different operational needs.
The existing spring screw includes a screw rod, a spring connecting sleeve, a spring, a fixed connecting sleeve, a nut and a nut sleeve, wherein the screw rod includes a screw cap, a connecting section without threads and a threaded connecting section with threads, and the connecting section is located in the screw cap and the thread. A shaft shoulder is arranged between the connecting sections and between the connecting section and the threaded connecting section, the connecting section of the screw is sleeved with a spring connecting sleeve, a spring and a fixed connecting sleeve, the spring connecting sleeve is close to the screw cap, and the connecting sleeve is connected between the spring connecting sleeve and the fixed connecting sleeve The connection spring is connected with a threaded nut on the threaded connection section of the screw, and the nut sleeve is connected to the nut sleeve. The fixed connection sleeve is fixedly connected to the upper die of the steel mold through bolts, and the nut sleeve is welded to the lower mold of the steel mold. When clamping the mold, a professional is required to turn the screw from the lower mold to the upper mold or hook it to the upper mold with a foot and then tighten it with the wind, which is inconvenient to install, has low work efficiency, and has potential safety hazards. Contents of the utility model Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. aims to provide a spring screw that is easy to operate. In order to solve the problems existing in the background technology, Guangdong Yueluo Hardware Industry Co., Ltd. adopts the following technical scheme: a spring screw, including a screw rod, an upper compression spring washer, a spring, a fixed sleeve, a lower compression spring washer, Base and fixing nut. The screw rod includes a screw cap, a connecting section without threads and a threaded connecting section with threads, the connecting section is located between the screw cap and the threaded connecting section, and a shaft shoulder is arranged between the connecting section and the threaded connecting section. The connecting section of the screw rod is sleeved with an upper compression spring washer, a spring, a fixing sleeve, a lower compression spring washer and a base, and the threaded connection section is connected with a fixing nut. A fixed sleeve is sleeved between the connection section and the threaded connection section, and the fixed sleeve is sleeved with a lower pressure spring washer and a base. The upper compression spring washer is close to the screw cap, the lower compression spring washer is fixed on the base by four screws, the spring is placed between the upper compression spring washer and the lower compression spring washer, and one end of the spring is sleeved with the upper compression spring washer , and the other end is sleeved with a fixed sleeve. For Yueluo, the diameter of the spring screw is between T20-T27. In this preferred solution, the use performance of the spring is high, which is beneficial to prolong the service life of the spring screw. For Yueluo, preferably, the thread connecting section of the screw adopts T-shaped thread. In this preferred solution, the fixing nut is tightly matched with the threaded connection section, so that the steel mold is clamped tightly. Yueluo is preferably made of 40Cr material for the fixing nut and screw. In this preferred solution, the rigidity of the fixing nut and the screw rod is high, which is beneficial to improve the usability of the spring screw. Yueluo is preferred, the spring screw parts except the fixing nut and the screw rod are made of 47# steel material. In this preferred solution, the production cost is low. In summary, Guangdong Yueluo Hardware Industry Co., Ltd. brings the beneficial effects: when the spring screw is used, it is only necessary to use a wrench to move the fixed nut, which is convenient for installation, disassembly and replacement, improving work efficiency and reducing production costs.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: GB5789 screws, acid and alkali resistant plastic screws, big ear hand-tightened ingot screw caps, 12.9 full-tooth screws and other products, we can provide you with products suitable for you fastener solutions.
