Service HotlineIn the automobile industry, it is often necessary to install bolts at the opening of a closed cavity to fix and connect other parts. However, the diameter of the opening of the closed cavity is often larger than that of the head of the bolt, so it is necessary to set a strip-shaped spacer on the head of the bolt, so that the spacer can penetrate the opening longitudinally, and then block the opening horizontally, so as to be stuck with an upside-down buckle. Bolt head. However, since the bolt body of the bolt has a certain length, the manual vertical and horizontal turning operation after the strip spacer penetrates the opening is very difficult, and it is easy to drop the bolt and the spacer into the airtight cavity together, which greatly increases the assembly time. Increased labor costs.
Washers are common parts that are annular or annular after compression. The existing standard washers include flat washers, spring washers, serrated lock washers, saddle washers, etc. The end faces are mostly flat or flat after compression. , so it is in surface contact with the workpiece. Generally, after the two workpieces are locked by washers, bolts and nuts, the workpieces cannot move in any direction, so as to achieve the purpose of tightening the two workpieces. In actual production, some workpieces are still required to be properly translated in a certain direction after locking. In order to achieve this requirement, the usual practice is to open a waist-shaped hole on the workpiece that needs to be moved, and the zigzag-shaped bushing is fitted with a flat washer after passing through the waist-shaped hole, as shown in FIG. The edge of the hole is located in the space enclosed by the bushing and the flat washer, and a gap is formed between the workpiece and the bushing and the flat washer, so that even if the bolt passes through the flat washer, the bushing and the workpiece in turn, it is threaded and locked with the nut. tight, the workpiece can still translate along the length of its girdle hole. Obviously, this method can achieve the requirement of proper translation of the workpiece, but the following deficiencies can still be found in the actual assembly. First, before locking, the bushing, washer and workpiece are separated from each other, so it is more inconvenient to assemble; secondly, the lining is The separation structure of the sleeve and the gasket is inconvenient to manage, and the disassembled gasket and bushing are easy to lose and affect the use again.
In the prior art, the beams used for installing the curtain wall are mainly divided into two types: closed-cavity structure and open structure, and angle aluminum connection is mainly used for the connection between the beam and the column. As far as the beam of the closed-cavity structure is concerned, after the angle aluminum is used to connect, there are open bolts on both ends of the upper surface of the beam, and the aesthetic performance is extremely poor. As far as the beam of the open structure is concerned, in the actual connection, first fix one corner of the angle aluminum to the beam, and then connect the other corner of the angle aluminum to the column; due to the limited operating space in the beam of the open structure, the angle aluminum is not It is easy and accurate to install, and it takes a lot of time to install; and when the curtain wall panel is heavy, the beam will be twisted, causing the gusset of the opening part of the beam to fall. In addition, due to the limitation of the opening structure itself (an additional gusset or clasp), the aluminum content of the beam is relatively heavy, and the manufacturing cost is high.
In order to solve the problem of poor waterproof performance of the existing rivets, Guangdong Yueluo Hardware Industry Co., Ltd. provides a waterproof rivet. By arranging a figure-eight waterproof part for waterproofing on the lower end surface of the waterproof cap, when the object is riveted, The waterproof cap is subjected to the pulling force of the rivet rod and the supporting force of the object. The pulling force and the supporting force cause the waterproof cap to generate stress, which in turn causes the waterproof part of the waterproof cap to be micro-deformed in the closest contact with the object, so as to achieve a good sealing effect.
The types of rivets can be roughly divided into open type, closed type, double drum type and single drum type series. The following is a brief description of their respective models. Countersunk head blind rivets: For the riveting of riveting parts that require smooth and beautiful surfaces after riveting. Double-drum blind rivet: During riveting, the mandrel pulls the end of the rivet body into a double-drum shape, clamps the two structural parts to be riveted, and can reduce the pressure acting on the surface of the structural parts. Uses: Mainly used for riveting various thin structural parts in various vehicles, ships, construction, machinery, electronics and other industries. Blind rivet with large brim: Compared with ordinary blind rivets, the diameter of the aluminum cap of this rivet is significantly larger. When the rivet is riveted with the connector, it has a larger contact area and a stronger supporting surface, which can enhance the torque Strength, can withstand higher radial tension. Applicable industry: It is suitable for fastening soft and fragile surface materials and extra-large holes. The increased diameter of the brim has special protection applications for soft materials. Closed Blind Rivet: Designed to wrap around the mandrel head after riveting, ideal for many applications where waterproofing is required. With high shear force, anti-vibration, anti-high pressure.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: six-sided screw caps, aluminum formwork pins, disc bolts, enlarged washers and other products, we can provide you with suitable fastener solutions for you Program.
