Service HotlineThe flat key is a key that relies on the two sides as the working surface and transmits the torque by the extrusion of the key and the side of the keyway, and is mostly installed on the shaft. If the flat key is used for a long time or is in a bad working environment for a long time, dust, oil, etc. will inevitably be stuck between the flat key and the keyway. Since the flat key has no ejector threaded hole for disassembly, it is difficult to dismantle, and during the disassembly process A little carelessness will cause damage to the flat key.
Ordinary thread Ordinary coarse thread: Feature code M+ Nominal diameter + Rotation + thread tolerance zone code (pitch diameter, top diameter) - Rotation length Ordinary fine thread: Feature code M+ Nominal diameter * thread pitch + direction of rotation + thread tolerance With code (middle diameter, top diameter) - the length of screwing is omitted for right-handed threads, and the left-handed thread is represented by LH. M 16-5g6g means coarse thread ordinary thread, nominal diameter 16, right-handed, the thread tolerance zone is 5g in the middle diameter and 6g in the major diameter, and the screwing length is considered as the medium length. M16×1 LH-6G means fine thread ordinary thread, nominal diameter 16, pitch 1, left-handed, thread tolerance zone medium diameter and major diameter are both 6G, and the screwing length is considered as medium length. The labeling format is: feature code (cylindrical pipe thread is represented by G, conical pipe thread is represented by NPT) + size code + tolerance grade code + rotation direction G1A--LH represents inch non-threaded sealing pipe thread, size code 1in, left-handed, tolerance The grade is A grade. Rcl/2 means inch thread seal taper pipe thread, size code 1/2in, right-handed.
The composition and proportion of this high-performance stainless steel screw thread are: 0.08%-0.15% C; 0.01%-0.60% Si; 0.02%-0.60% Mn; 0.01%-0.03% P; 0.002%- 0.03% S; 12%-14% Cr; 0.8%-1.5% Mo and the rest is Fe. The preparation method includes the following steps: smelting molten steel according to chemical composition requirements; hot rolling; annealing and pickling to obtain a stainless steel plate blank; coating and drying; cold drawing; cleaning and drying with a neutral activator; quenching; tempering ; coated and dried; drawn into stainless steel thread. This high-performance stainless steel screw line is energy-saving and environmentally friendly, with high corrosion resistance, high elasticity and high toughness. The preparation method and process are advanced and simple, and the production cost is low.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide an improved lock nut to solve the problem that the production technology of the prior art products is too complicated. For realizing the above-mentioned purpose, Guangdong Yueluo Hardware Industry Co., Ltd. adopts following technical scheme—a kind of locking nut, which comprises that the bottom of the nut is a circle, the middle part is a hexagon, and the top is a circle, and there are bolts in the center.
The cylindrical pin is mainly used for positioning and can also be used for connection. It is fixed in the pin hole by means of interference fit. Cylindrical pins used for positioning are usually not subject to load or a small load, the number is not less than two, distributed in the symmetrical direction of the overall structure of the connected parts, the farther the better, the pin is in each connected part The length is about 1-2 times the minor diameter. Cylindrical pins can also be used as shafts, and a straight shaft can also be used as cylindrical pins or even centering pins. So what's the difference between a shaft and a pin? The shaft can be used to transmit torque, bear bending moment and torque, and the cylindrical pin can be used for positioning, bear extrusion force and shear force. In a sense (such as small equipment), cylindrical pins can also be used as shafts.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: phosphating plants, extended switch screws, solid pressure rivets, Q190 screws and other products, we can provide you with suitable fastener solutions for you.
