Service HotlineAt present, many manufacturers do not want the product to be disassembled by the user, so they set the anti-disassembly mark on the product. The common method is to apply red or blue anti-disassembly paint on the fastener, such as the nut, once the user disassembles it by himself. , the paint at the connection will fall off, and it can no longer be aligned, so that the manufacturer can judge and identify it and provide a basis for warranty. However, it is inconvenient to paint some joints, and the use of tamper-evident paint is not healthy and environmentally friendly.
Knurled copper nut, the specification is M5X8X12, the outer circle is 8.0MM, and the height is 12MM. Material: C3604 (ROHS PASS) brass. The thread still guarantees 6H accuracy. This knurled copper nut is used in power tools. Unlike other knurled copper nuts, the diamond pattern of this knurled copper nut is located in the middle of the product, and the diamond-shaped mesh knurled wheel edge The large outer circular step surface is rolled out of diamond-shaped flowers.
spring washer is installed under the nut to prevent the nut from loosening. It is stated in the national standard. Hexagonal slotted nuts are specially designed for use with bolts with holes at the end of the screw, so that the cotter pin can be inserted into the hole of the screw from the groove of the nut to prevent the nut from automatically loosening. It is mainly used for vibration loads or alternating loads. . The methods to prevent the nut (or bolt) from automatically loosening in the mechanical design and production are as follows: 1. Add a spring washer; (simple and easy to do) 2. Use a hexagonal slotted nut + a split pin; (increase the processing process) 3 . Pad the stop washer; (increase the processing process compared with the same period of last year) 4. Insert the steel wire into the hexagon head opening of the hexagon bolt. (Increased processing steps compared to the same period of last year) Spring washers are used to prevent loosening. For example, the bolts connecting the motor and the machine base generally need to add spring washers, because the motor vibrates without the spring washers, and the nuts will loosen. Generally, the fasteners on the equipment with vibration There is a spring gasket on it, and there is generally no need to add a gasket on the flange! Whether the spring gasket is added to the flange is related to the medium circulating in the pipeline. If it is easy to generate pulses, it is best to add spring gaskets, as well as high-speed fluid, and the caliber changes frequently. Do not generalize. On some valves, the stuffing box gland All flanges need to be added with spring gaskets. The automatic selection of spring gaskets is included.
Countersunk head screws are mostly used after installation, and the surface of the parts cannot be raised, and the parts to be fastened have two thicknesses. Thickness, after the screw is tightened, there is still a part of the screw thread that does not enter the threaded hole. In this case, the countersunk head screw can definitely be tightened. There is usually a situation where the thickness of the fastened part is less than the height of the head of the countersunk head screw, which is commonly seen in sheet metal parts in mechanical equipment, such as the connection between the hinge of the chassis and the door and the box; the sheet metal of the equipment The connection of the cover to the equipment, etc. Due to the small thickness of the part, the tightened sheet metal part, the screw through hole completely becomes a conical hole, in this case, when the countersunk head screw is tightened, the screw head is not a tapered surface to press the sheet metal part , but the bottom of the screw head and the top of the threaded hole are squeezed. Although it feels that the screw is tightened, the sheet metal part is stuck instead of being pressed. In this case, although it feels that the screw is tightened, the sheet metal The gold pieces were indeed not tightened. This is a very common situation. Let’s talk about the reasons for the processing: the head cone of the countersunk screw has a 90° conical angle, and the apex angle of the newly bought drill is usually 118°-120°. Some workers who lack training do not know this angle is poor. It is often used to ream the hole with a 120° drill bit, which results in that when the countersunk head screw is tightened, it is not the conical surface of the head, but a line at the bottom of the screw head, which is one of the reasons why the so-called countersunk head screw cannot be tightened. , it's not the screw's fault.
The isolating switch in the substation has a large workload for maintenance. The transmission parts such as the isolating switch connecting rod are mostly connected by cylindrical pins. The shaft-pin fit is generally 1mm, which is tight. If the cylindrical pin is disassembled during the maintenance process, it is often due to corrosion and mechanical deformation. It is difficult to proceed smoothly for other reasons, and if the working environment is a small space, it is more difficult to disassemble. In traditional operations, grinding, hard prying, or beating with a hand hammer are often used to disassemble, which will further deform the pins, and when the space is small, it is difficult to use tools such as hand hammers. solve.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: GB5789 bolts, round cups with washers with washers, galvanized washers, 8-grade white-plated nuts and other products, we can provide you with products suitable for you fastener solutions.
