Service HotlineIn the process of electronic accessories such as mobile phones and computers, especially multi-layer circuit boards, there are generally fixed connections between multi-layer circuit boards or other components. At present, there are two main connection methods. One is to use laser welding. However, the laser welding equipment is expensive and has very high requirements on the position of the weldment. Therefore, during welding, it must be ensured that the final position of the weldment needs to be the same as the laser beam will impact. Solder joint alignment. The other is to use a metal rivet to pass through the positioning hole, and then impact the rivet with a punching needle, so that the open end of the rivet is deformed and opened and pressed on the fixed piece to form a rivet fixed state. However, in actual operation, when the open end of the rivet tube is opened and deformed by the impact, strong cracking often occurs, resulting in a small amount of conductive fracture debris, which falls on the circuit board or other devices to be connected, causing Short circuit, in view of this shortcoming, some manufacturers have changed the metal rivets to plastic materials, but the plastic rivets have poor ductility and often break when impacted with a punching needle, resulting in the failure to achieve the riveting fixing force of the original metal rivets. In addition, the above two fixing methods are complicated in operation and low in installation efficiency.
At present, in the power industry, for the fixing of terminals, most of the terminals are directly locked to the fixing screws using U-shaped clips. However, since the contact surface often cannot reach the level of flatness, it will cause difficulties in locking, and it will take a long time. Easy to loose and fall off. Although the use of spring clips is effective, due to the influence of its own width, the use of spring clips is not very extensive. Contents of the utility model The purpose of Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to provide an automatic locking screw for fixing the U-shaped clip. In order to achieve the above purpose, Yueluo adopts the following technical solutions: an automatic locking screw. From bottom to top, there are screw head, screw rod and nut with external thread. The screw rod is a hollow screw rod, and the hollow screw rod is on both sides. Long holes are respectively provided, the width of the long holes is smaller than the inner diameter of the hollow screw rod, a spring is arranged in the inner cavity of the hollow screw rod, the upper end of the spring is provided with a plug, and the two wings of the plug protrude out of the hollow screw rod through the long hole. The spring described by Yueluo is not less than the length of the hollow screw rod in the free extension state. The distance between the two wings of the plug described by Yueluo is greater than the diameter of the nut. Yueluo adopts Guangdong Yueluo Hardware Industry Co., Ltd., which can easily realize the automatic locking of the U-shaped clamp, and can be adjusted according to the thickness of the U-shaped clamp to ensure the close contact between the U-shaped clamp and the connecting screw.
The existing screw generally includes a round table-shaped nail body with one large end and one small end, a threaded section is provided on the radial circumference of the nail body, a small end of the nail body is provided with an inclined tip, and the large end of the nail body is provided with a nail cover. , generally used on materials that are softer than the screw, and drill into the object to be nailed through its own rotation. When drilling, the thread plays the role of rotary cutting, so that the screw is drilled forward, but when the thread cuts the object to be nailed When it is shaken for a long time, the tightening force of the screw in the axial direction is not enough, it is easy to loosen, and there is a potential safety hazard.
The screw refers to the screw (foreign name: Screw), which is a tool that uses the physical and mathematical principles of the oblique circular rotation of the object and the frictional force to gradually fasten the utensils and parts. A screw is a common term for fasteners, an everyday colloquial language. Metric threads are measured in MM (millimeters) and have a cusp angle of 60 degrees. Both US and Imperial threads are measured in inches. The cusp angle of the American thread is also 60 degrees, while the cusp angle of the imperial thread is 55 degrees.
Stainless steel screws usually refer to steel screws that are resistant to corrosion by air, water, acids, alkali salts or other media. Stainless steel screws are generally not easy to rust and durable, and can be used in environmental protection equipment, medical equipment, communication equipment and other fields.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: galvanized gasket manufacturers, American standard bolts, half-tooth socket head cap screws and bolts, corrugated flat washers and other products, we can provide you with suitable products for you. Fastener Solutions.
