Service HotlineDouble-end stud (English name: double-end stud) refers to a cylindrical fastener with threads at both ends. Widely used in electric power, chemical industry, oil refining, valves, railways, bridges, steel structures, automobile and motorcycle accessories, machinery, boiler steel structures, pendant towers, large-span steel structures and large buildings.
Stainless steel screws do not necessarily corrode and rust, but that stainless steel screws have a stronger ability to withstand corrosion and rust than iron screws. But stainless steel screws can still rust under certain circumstances. So under what conditions are stainless steel screws prone to rust! What is the cause of rust? Stainless steel screws have better characteristics, strong corrosion resistance, high temperature resistance, and strong rust resistance. But it will rust in harsh environments. For example, stainless steel screws are exposed to the sun and the wind every day under very humid conditions. Over time, it will definitely rust a little. For example, in contact with some acid-base chemicals to cause chemical reactions. cause corrosion and rust. There are also bad stainless steel screws, such as stainless steel SUS201 screws used in seawater. Due to long-term immersion, SUS201 stainless steel screws themselves are not suitable for use in salty seawater. cause corrosion and rust. For the use of marine products, it is generally recommended to use stainless steel SUS316 screws, because 316 stainless steel screws have better performance such as corrosion resistance. From the above, it can be concluded that stainless steel screws will still corrode and rust under certain circumstances. Therefore, this requires the rational use of stainless steel screws. Use stainless steel screws of different materials in different situations. And in different occasions, when using stainless steel screws, special attention is also required, and some details need to be considered more. Try to control the corrosion and rust of stainless steel screws as much as possible.
When installing the ventilation duct, because the gap between the air duct and the wall and between the air duct and the air duct is deep and narrow, the arm cannot enter into it to operate, which brings about the installation of the screws and nuts at these positions. The following three methods are generally used: one is to directly break the wall for installation, but this method damages the building greatly, and cannot be used for the installation of screws and nuts in the gap between the air ducts; the other is to Set the inner flange in the air duct and connect it with bolts, which will reduce the effective cross-sectional area of the air duct and increase the resistance of the gas flow. Moreover, people need to enter the air duct for construction during installation. Considering the size of the air duct First, the supporting firmware with a high position and no force has certain hidden dangers; third, it is directly ignored and not done, but it is easy to cause the air duct connection is not tight and the air volume loss is large. The above-mentioned methods all have major construction defects, which not only waste a lot of manpower and time in the construction process, but also have the problem of low air supply efficiency.
1. Grade C washers do not have Ra3.2 and deburring requirements. 2. Grade C is suitable for medium assembly series, Grade A is suitable for fine assembly series 3. G B848-85 is mainly used for cylinder head screws, others are used for standard hexagon bolts, screws and nuts. 4. Material mechanical property grade: steel 200HV; austenitic stainless steel A200. 5. Marking example: standard series, nominal size d=8mm, flat washer with performance level of 200HV and no surface treatment: washer GB97.1—85 8 200HV
GB97.1.CATPart GB97.1.SLDPRT Nominal size d d1 d2 h 1000 weight (kg) ≈ nominal diameter (NND) inner diameter (SD1) outer diameter (SD2) thickness (SD) — 5 5.3 10 1 0.443 Spring washer spring Wasket 6 6.4 12 1.6 1.0518 8.4 16 1.6 1.828 10 10.5 20 2 3.57 14 15 28 2.5 8.611 16 17 30 3 11.29 20 21 37 37.16 24 25 44 4 32.31 30 31 56 4 53.61 36 37 66 5 92.03
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: oil plug bolts, pull-out bolts with rings, jack screws, anti-slip flange nuts with pads and other products, we can provide you with The right fastener solution for you.
