Service HotlineWith the continuous improvement of road facilities, guardrails are set up in the middle of the roads in most cities at the separation of the upper and lower lanes. At the same time, guardrails are also set up between the motor vehicle lane and the non-motor vehicle lane. The bottom of the guardrail column is set with a base, and the base is usually made of If the steel nail is fixed, the deformation hole should be drilled on the asphalt road first, and then the steel nail should be knocked into the deformation hole. Because the outer wall of the steel nail is cylindrical, the friction force on the ground is small, and the guardrail is affected by the deformation. When the external impact force occurs, the steel nails are easily detached from the asphalt road, making the road guardrail lose its fixation. In some places, expansion screws are used to fix the railings, but during the tightening process of the expansion screws, the expansion pieces are opened by the force of the ejector rod, and the opening angle is small. Limited, the railing will still fall down when subjected to a large impact. Therefore, it is necessary to design a special screw for fixing the railing on the asphalt road.
With the development of science and technology, human construction technology has also continued to improve. In terms of tools used in construction, it is constantly innovating and bringing forth new ideas, in order to enable personnel operating on construction sites to work more safely and efficiently; among them, screws The belt has become an indispensable auxiliary tool in the construction industry, especially for those who need to operate in a more dangerous high position. With the assistance of a nailing machine and a screw belt, it is quite convenient to screw together. Locked work to improve work safety and efficiency.
A pull rivet, this kind of pull rivet has good installation performance, firm connection and long service life, but the defects are: first, after installation and use, if it is damaged, it cannot be reused; second, it is convenient to disassemble, and it also increases the possibility of theft ,. It is not conducive to safety; 3. There is still the possibility of movement in the circumferential direction of the collar, which will affect the riveting effect.
For achieving the above purpose, Guangdong Yueluo Hardware Industry Co., Ltd. provides the following technical solutions: a pin, comprising a pin cap and a described pin rod, the pin cap and one end of the pin rod are fixedly connected, and the pin rod There is a convex body, the convex body is fixedly connected with the pin rod, the convex body is located on the pin rod rod body, and the other end of the pin rod is provided with a top connecting body, and the top connecting body is fixedly connected with the pin rod , the top contact body includes several top contact units and discs, each top contact unit is coaxially arranged with the pin rod, the top contact units are sequentially fixedly connected along the axis direction of the pin, the top contact unit is The major diameter of the outer contour of the connecting body is larger than the diameter of the pin rod.
In another embodiment of Guangdong Yueluo Hardware Industrial Co., Ltd., the conveying device 3 includes a motor 31 and a circular rotating disk 34, the motor 31 drives the circular rotating disk 34 to rotate, and the circular rotating disk 34 is evenly provided with screws in the circumferential direction. The matching screw accommodating hole 35, the screw enters the screw accommodating hole 35, the motor 31 drives the circular rotating plate 34 to rotate, so that the screw is first slotted by the cutting wheel 42, and then polished by the fixing wheel 48, and the screw is in the screw accommodating hole 35. It is fixed, which is more secure and reliable during the slotting process. Preferably, the circular rotating disk 34 includes a circular rotating disk 32 and a sector-shaped fixed disk 33. The circular rotating disk 32 is evenly provided with screw receiving recesses matching the screws in the circumferential direction, and the recesses and the sector-shaped fixed disk 33 are formed with the screws The matching screw receiving holes face the cutting wheel 42 and the fixing wheel 51 .
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: nylon locking lock nuts, hardware screws, square four-corner nuts, external serrated anti-skid washers and other products, we can provide you with suitable tightening. Firmware Solutions.
